动态导航技术在定位钙化根管中的三维精度
本研究旨在提出一种新型动态导航方法以实现微创开髓,并评估其在上下颌牙模拟高度困难钙化根管定位中的三维精度。使用三套相同的上下颌3D打印颌骨模型(含84颗牙、138个模拟钙化根管),由认证牙髓病专家使用Navident动态导航系统随机规划并执行高速手机开髓。结果显示2D水平偏差均值0.9mm,3D偏差均值1.3mm,3D角度偏差均值1.7度,平均钻磨时间57.8秒。
要点
- 动态导航辅助开髓定位钙化根管的2D水平偏差均值0.9mm,3D偏差均值1.3mm。
- 3D角度偏差均值1.7度,磨牙显著高于前磨牙。
- 2D和3D偏差与根管口深度无关,平均钻磨时间57.8秒。
核心结论
- 动态三维导航技术配合高速手机在牙髓钙化患牙中具有保留牙体组织和准确定位根管的潜力。
研究设计与样本
- 体外研究,使用三套相同的上下颌3D打印颌骨模型,含84颗牙和138个模拟钙化根管,置于牙科仿头模上。
- 由一名委员会认证的牙髓病专家使用Navident动态导航系统随机规划并执行高速手机开髓。
- 通过叠加锥形束CT扫描数字化测量计划与实际开髓洞之间的2D和3D水平、垂直及角度偏差。
主要发现
- 距根管口的平均2D水平偏差为0.9mm,上颌牙显著高于下颌牙(P < .05)。
- 距根管口的平均3D偏差为1.3mm,上颌牙略高于下颌牙(P ≥ .05)。
- 平均3D角度偏差为1.7度,磨牙显著高于前磨牙(P < .05)。
- 3D和2D偏差与根管口深度无关(P > .05)。
- 平均钻磨时间为57.8秒,显著依赖于根管口深度、牙类型和颌骨(P < .05)。
临床怎么用
- 动态导航可辅助微创开髓,在钙化根管定位中实现毫米级偏差和较小角度偏差。
- 上颌牙和磨牙的偏差相对较高,临床操作中需注意这些牙位的精度控制。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: This study aimed to present a novel dynamic navigation method to attain minimally invasive access cavity preparations and to evaluate its 3-dimensional (3D) accuracy in locating highly difficult simulated calcified canals among maxillary and mandibular teeth. METHODS: Three identical sets of maxillary and mandibular 3D-printed jaw models composed of 84 teeth in their anatomic locations with simulated calcified canals (N = 138 canals) were set up on dental manikins. The Navident dynamic navigation system (ClaroNav, Toronto, Ontario, Canada) was used to plan and execute access preparations randomly with high-speed drills by a board-certified Endodontist. Two-dimensional (2D) and 3D horizontal, vertical, and angulation discrepancies between the planned and placed access preparations were digitally measured using superimposed cone-beam computed tomographic scans. Analysis of covariance models were used to evaluate the associations and the interaction between tooth type and jaw, the canal orifice depth, and the discrepancies between planned and prepared access cavities. The significance level was set at .05. RESULTS: The mean 2D horizontal deviation from the canal orifice was 0.9 mm, and it was significantly higher on maxillary compared with mandibular teeth (P < .05). The mean 3D deviation from the canal orifice was 1.3 mm, and it was marginally higher on maxillary teeth in comparison with mandibular teeth (P ≥ .05). The mean 3D angular deviation was 1.7 degrees, and it was significantly higher in molars compared with premolars (P < .05). The 3D and 2D discrepancies were independent of the canal orifice depths (P > .05). The average drilling time was 57.8 seconds with significant dependence on the canal orifice depth, tooth type, and jaw (P < .05). CONCLUSIONS: This study shows the potential of applying dynamic 3D navigation technology with high-speed drills to preserve tooth structure and accurately locate root canals in teeth with pulp canal obliteration.
引用
- Jain SD, Carrico CK, Bermanis I, et al. 3-Dimensional Accuracy of Dynamic Navigation Technology in Locating Calcified Canals. J Endod. 2020. PMID: 32340763. doi:10.1016/j.joen.2020.03.014
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。