模拟根管内加热对环氧树脂和氧化锌丁香油封闭剂理化性质的影响
实验室研究将AH Plus和Pulp Canal Sealer在37至97°C加热30秒,并在97°C加热60和180秒,检测固化时间、流动性和膜厚度及FT-IR。随温度和时长增加,两种封闭剂固化时间缩短,但不超过60秒加热时理化性质无实质变化,支持其用于热垂直加压充填。
要点
- 不超过60秒的临床相关加热未导致两种封闭剂理化性质实质改变。
- AH Plus和PCS的固化时间随加热温度和时长增加而缩短。
- 97°C加热180秒使PCS立即固化,超出临床推荐条件。
核心结论
- 模拟临床相关温度和加热时间(不超过60秒)的热处理未导致两种封闭剂任何实质物理或化学变化。
- AH Plus和Pulp Canal Sealer可被认为适用于热根管充填技术。
研究设计与样本
- 实验室研究,将AH Plus和Pulp Canal Sealer在37、47、57、67、77、87和97°C加热30秒,并在97°C加热60和180秒。
- 试样在2 mL塑料管中于温控水浴加热至目标温度并保持设定时间,冷却至体温后评估物理性质(ISO 6876)。
- 化学性质在37°C、100%湿度孵育至完全固化后采用傅里叶变换红外光谱评估。
- 物理性质统计分析采用Kruskal-Wallis检验(P = 0.05)。
主要发现
- AH Plus固化时间从20°C(30秒)的622分钟降至97°C(180秒)的381分钟(P < 0.05)。
- PCS在97°C加热180秒导致材料立即固化。
- PCS固化时间从20°C(30秒)的80.1小时降至97°C(30秒)的41.0小时(P < 0.05)。
- 除PCS在97°C加热180秒外,膜厚度和流动性未受热处理明显影响。
- FT-IR光谱未显示两种封闭剂热处理后有任何化学变化。
关键数值与推荐
- 临床相关考虑:热垂直根管充填时根管内封闭剂温度可能不超过60°C。
- 连续波技术推荐加热时间少于30秒,但复杂病例可能超过此阈值。
临床怎么用
- 在热垂直加压充填中,AH Plus和PCS在加热不超过60秒时理化性质稳定,可安全使用。
- 应避免对PCS进行97°C持续180秒的过度加热,以免材料立即固化。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIM: To gain information in a laboratory setting about the effect of thermal treatment of epoxy resin-based and zinc oxide-eugenol-based sealers. METHODOLOGY: AH Plus and Pulp Canal Sealer (PCS) were exposed to thermal treatment at 37, 47, 57, 67, 77, 87 and 97 °C for 30 s. According to clinically relevant considerations, intracanal sealer temperature is likely not to exceed 60 °C during warm vertical root canal filling. Heat application is recommended for less than 30 s during continuous wave technique, but might exceed this threshold in complex cases. Furthermore, heat treatment at 97 °C was performed for 60 and 180 s to simulate inappropriate implementation of warm vertical filling techniques. Specimens were heated inside 2-mL plastic tubes in a thermo-controlled water bath until the temperatures were reached and kept at this temperature for the determined period of time. Afterwards, specimens were cooled to body temperature and physical properties (setting time, flow, film thickness according to ISO 6876) were assessed. Chemical properties (Fourier transformed infrared spectroscopy) were assessed after complete setting of the specimens in an incubator at 37 °C and 100% humidity. Statistical analysis of physical properties was performed using Kruskal-Wallis test (P = 0.05). RESULTS: The setting time of AH Plus and PCS decreased when temperature and duration of heat application increased. Whilst the setting time of AH Plus decreased from 622 min at 20 °C (for 30 s) to 381 min at 97 °C (for 180 s; P < 0.05), heat treatment of PCS at 97 °C for 180 s led to an immediate setting of the material. From 20 °C (for 30 s) to 97 °C (for 30 s), the setting time of PCS decreased from 80.1 to 41.0 h (P < 0.05). Film thickness and flow were not relevantly influenced by thermal treatment except for PCS at 97 °C for 180 s. FT-IR spectroscopy did not reveal any chemical changes of either sealer after thermal treatment. CONCLUSIONS: Thermal treatment simulating clinically relevant temperature levels and heating times did not lead to any substantial physical or chemical changes at all temperature levels when heating did not exceed 60 s. AH Plus and Pulp Canal Sealer can be considered suitable for warm root filling techniques.
引用
- Donnermeyer D, Urban K, Bürklein S, et al. Physico-chemical investigation of endodontic sealers exposed to simulated intracanal heat application: epoxy resins and zinc oxide-eugenols. Int Endod J. 2020. PMID: 31955439. doi:10.1111/iej.13267
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。