文献速递牙体牙髓病

四种根管锉系统对工作长度变化及根管弯曲度影响的比较研究

Comparative Study of Four Endodontic File Systems to Assess Changes in Working Length during Root Canal Instrumentation and the Effect of Canal Curvature on Working Length Change.
PubMed 文献 · J Endod · 2019-11-15

研究使用80个塑料根管模型(弯曲度10°和30°各40个),比较Hedström、K、ProTaper Next和TF Adaptive四种锉系统在根管预备中工作长度减少和根管扩大量。结果显示镍钛旋转锉(ProTaper Next和TF Adaptive)在维持工作长度和减少根管扩大方面优于不锈钢手用锉,Hedström锉显著优于K锉;根管弯曲度增加时K锉和ProTaper Next的工作长度减少显著增加,K锉的根管扩大也显著增加。

要点

  • 镍钛旋转锉比不锈钢手用锉更能维持工作长度并减少根管扩大。
  • Hedström锉在减少工作长度变化和根管扩大方面显著优于K锉。
  • 根管弯曲度增大时,K锉和ProTaper Next的工作长度减少显著增加。

核心结论

  • 镍钛旋转锉在维持工作长度和减少根管扩大方面优于不锈钢手用锉。
  • Hedström锉在减少工作长度变化和根管扩大方面显著优于K锉。

研究设计与样本

  • 使用80个塑料根管模型,弯曲度10°和30°各40个,每种锉系统各预备10个10°和10个30°模型至25号。
  • 预备前后测量工作长度,并通过叠加照片计算面积差异。

主要发现

  • ProTaper Next和TF Adaptive产生的工作长度减少和根管扩大最小,其次为Hedström锉和K锉。
  • 使用K锉和ProTaper Next时,根管弯曲度增加显著增加工作长度减少。
  • 使用K锉时,根管弯曲度增加显著增加根管扩大。

临床怎么用

  • 在根管预备中优先选择镍钛旋转锉以维持工作长度并减少根管扩大。
  • 对于弯曲根管,使用K锉时需注意工作长度减少和根管扩大增加的风险。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The aim of this study was to compare a reduction in working length and area of canal enlargement resulting from instrumentation with Hedström (Kerr Dental, Orange, CA), K (Kerr Dental), ProTaper Next (Dentsply Sirona, York, PA), and TF Adaptive (Kerr Dental) files. The effect of the canal curvature on the working length and area of canal enlargement was also assessed. METHODS: A total of 80 plastic canal models were used, 40 with a canal curvature of 10° and another 40 with a canal curvature of 30°. Instrumentation of 10 models with a 10° canal curvature and 10 models with a 30° canal curvature was performed using each of the file systems up to size 25. Working length measurements were taken before and after instrumentation with each file type and size. Twenty composite images were made from superimposition of pre- and postpreparation photographs, and the difference in area was calculated using ImageJ software (National Institutes of Health, Bethesda, MD). RESULTS: ProTaper Next rotary files and TF Adaptive files produced the smallest reduction in the working length and the least canal enlargement followed by Hedström files and K files, respectively. The degree of canal curvature increased the working length reduction by a significant amount when K files and ProTaper Next rotary files were used, and the degree of curvature increased canal enlargement by a significant amount when K files were used. CONCLUSIONS: Nickel-titanium rotary files produced more favorable results than stainless steel hand files in terms of maintaining a consistent working length and producing minimal canal enlargement. Hedström files performed significantly better than K files in terms of working length reduction and canal enlargement.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Tien M, Tjoa H, Zhou M, et al. Comparative Study of Four Endodontic File Systems to Assess Changes in Working Length during Root Canal Instrumentation and the Effect of Canal Curvature on Working Length Change. J Endod. 2019. PMID: 31740067. doi:10.1016/j.joen.2019.10.004

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。