改良口内导板技术用于磨牙引导牙髓治疗一例
本文报告一例52岁男性上颌第一磨牙因根管钝化导致远颊根管无法定位的病例。采用锥形束CT与牙齿表面扫描数据融合制作导板,并将钻针路径通过复合树脂转化为口内导板,成功完成引导牙髓治疗。这是首例在咬合间距受限的磨牙中应用引导开髓的病例报告。
要点
- 引导牙髓治疗融合CBCT与表面扫描数据制作钻针路径导板
- 磨牙区咬合间距不足时,可将虚拟路径转化为复合树脂口内导板
- 本病例成功对远颊根管钝化的上颌磨牙完成引导开髓
核心结论
- 对于咬合间距受限的磨牙,将虚拟钻针路径转化为复合树脂口内导板可完成引导开髓。
研究设计与样本
- 个案报告:52岁男性,上颌第一磨牙(#3)远颊根管钝化伴根尖周病变,常规方法无法定位根管。
主要发现
- 腭根、近中颊根及第二近中颊根经手用锉和冠部扩展建立滑行路径后,用25号往复锉到达工作长度。
- 远颊根管在手术显微镜下也无法疏通,最终采用引导牙髓治疗完成开髓。
关键数值与推荐
- 使用10号手用锉建立滑行路径,并以25号往复锉进一步预备至工作长度。
- 所有3个根管临时封入氢氧化钙。
- 根据CBCT与表面扫描融合数据制作含套筒的透明SICAT Optiguide导板。
临床怎么用
- 磨牙区咬合间距不足时,可先临时充填光固化复合树脂,通过导板套筒压入钢针将钻针方向转移至复合树脂。
- 复合树脂聚合后移除导板与钢针,即可基于复合树脂基座进行引导钻孔。
局限性
- 本文为单一病例报告,结论的外推需谨慎。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
The aim of this case report was to show the concept of guided endodontics in a maxillary first molar with limited interocclusal space. Guided endodontics involves merging cone-beam computed tomographic imaging and a surface scan of the tooth in order to create a guide to perform a drill path into the seemingly obliterated root canal. In the molar region, the interocclusal space is often too small to accommodate the guide, bur, and handpiece at once, and, therefore, a modified approach is presented. A 52-year-old man was referred because the dentist had failed to localize the distobuccal root canal of a maxillary molar (#3) associated with apical pathosis. After reopening and rubber dam placement, a glide path was established for both the palatal first mesiobuccal root canal and the second mesiobuccal using a size 10 hand file and coronal flaring. Further instrumentation to the working length was achieved by reciprocating file size 25. All 3 canals were temporarily filled with calcium hydroxide. For the distobuccal root canal, guided endodontics was chosen in order to avoid further impairment of the tooth because negotiation of the canal failed even with the use of the operating microscope. Following the merged data obtained from the cone-beam computed tomographic and surface scans, a translucent SICAT Optiguide (SICAT, Bonn, Germany) was constructed containing a sleeve representing the proper direction of a drill path in order to reach the distobuccal root canal. The access cavity was temporarily filled with a composite material made for light-curing. Before light curing, the Optiguide was replaced on the teeth, and a steel pin was pressed through the sleeve and the composite whereby the proper drill path direction was transferred into the composite. After polymerization and removal of the Optiguide and pin from the composite base sleeve, the guided drilling could be performed. This case report is the first on guided access preparation in a molar with pulp canal obliteration and limited interocclusal space. The demand for more interocclusal space was solved by transforming the virtual drill path into a composite-based intracoronal guide. The use of digital technology was essential.
引用
- Buchgreitz J, Buchgreitz M, Bjørndal L, et al. Guided Endodontics Modified for Treating Molars by Using an Intracoronal Guide Technique. J Endod. 2019. PMID: 31056301. doi:10.1016/j.joen.2019.03.010
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。