不同热处理镍钛器械预备重度弯曲根管的几何形态与中心定位能力变化:显微CT研究
预备后所有参数显著增加,颈三分之一RC与RCB平均增加量高于PTN与TRU,根尖三分之一各系统无显著差异。结论为锥度较大的器械可能引起更大形态变化,但根尖危险区各系统在尺寸变化与根管偏移上无差异。
要点
- 预备后根管二维与三维形态参数均显著增加。
- 颈三分之一RC与RCB平均增加量高于PTN与TRU。
- 根尖三分之一各系统尺寸变化与根管偏移无显著差异。
核心结论
- 锥度较大的器械可能促进更大的形态学变化。
- 无论器械数量、运动方式、合金热处理类型及器械特征如何,各系统在关键根尖区未导致不同的尺寸变化和根管偏移。
研究设计与样本
- 根据相似形态尺寸匹配后分为4组(n=8):ProTaper Next、Reciproc、Reciproc Blue和TRUShape。
主要发现
- 预备显著增加了所有分析的参数。
- RC与RCB之间以及PTN与TRS之间在任何分析参数上均无统计学显著差异(P > .05)。
- 颈三分之一RC和RCB的平均增加量高于PTN和TRU。
- 根尖三分之一各系统间无统计学显著差异(P > .05)。
临床怎么用
- 对于重度弯曲根管,所选系统在根尖区的尺寸变化和根管偏移表现相似。
- 颈三分之一需注意不同系统可能带来更大的形态学变化。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The aim of this study was to compare the shaping ability of 4 different nickel-titanium systems, considering their variation in alloy treatment, kinematics, and design, used to prepare canals with severe curvature using micro-computed tomographic analysis. METHODS: Thirty-two mesial roots of mandibular molars with severe curvature were matched based on similar morphologic dimensions and assigned to 4 experimental groups (n = 8) according to the canal preparation: ProTaper Next (PTN; Dentsply Maillefer, Ballaigues, Switzerland), Reciproc (RC; VDW GmbH, Munich, Germany), Reciproc Blue (RCB, VDW GmbH), and TRUShape (TRU; Dentsply Tulsa Dental Specialties, Tulsa, OK) systems. Changes in 2-dimensional (area and perimeter) and 3-dimensional (volume, surface area, and structure model index) morphologic parameters as well as canal transportation were compared among groups using the analysis of variance post hoc Tukey tests with the significance level set at 5%. RESULTS: Preparation significantly increased all analyzed parameters. No statistically significant differences (P > .05) were observed between RC and RCB or between PTN and TRS in any of the analyzed parameters. In the cervical third, RC and RCB presented higher mean increases than PTN and TRU. In the apical third, there were no statistically significant differences (P > .05) among the systems. CONCLUSIONS: The instruments of greater taper may promote greater morphologic changes. However, regardless of the number of instruments (multiple or single), the type of movement (rotation or reciprocating), the type of heat treatment of alloys, and the particular characteristics of each instrument (taper and design), the evaluated systems did not result in different dimensional changes and canal transportation in the critical apical area.
引用
- Filizola de Oliveira DJ, Leoni GB, da Silva Goulart R, et al. Changes in Geometry and Transportation of Root Canals with Severe Curvature Prepared by Different Heat-treated Nickel-titanium Instruments: A Micro-computed Tomographic Study. J Endod. 2019. PMID: 30954280. doi:10.1016/j.joen.2019.02.018
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。