文献速递牙体牙髓病

三种镍钛机动系统对离体上颌第一磨牙MB2根管的疏通与成形能力:micro-CT研究

The ability of three nickel-titanium mechanized systems to negotiate and shape MB2 canals in extracted maxillary first molars: a micro-computed tomographic study.
PubMed 文献 · Int Endod J · 2018-12-25

本研究用micro-CT评估三种不同镍钛合金制成的机动镍钛锉系统对离体上颌第一磨牙MB2根管的预备效果。结果显示三组根管偏移和中心定位能力无显著差异,但ProDesign R去釉质体积更少、无穿孔且操作时间更长。

要点

  • 三组镍钛系统预备MB2根管的根管偏移和中心定位能力无显著差异(P > 0.05)。
  • ProDesign R组根管体积和去釉质体积显著低于Mtwo和Reciproc组(P < 0.05)。
  • Mtwo和Reciproc组各检测到一例根穿孔,ProDesign R组无穿孔;ProDesign R操作时间显著更长。

核心结论

  • 所有镍钛系统预备MB2根管后的根管偏移、中心定位能力和根尖区体积增加相似。
  • ProDesign R(25号,.06锥度)去釉质体积更少、无根穿孔,但完成根管预备所需时间更长。

研究设计与样本

  • 三组分别使用Reciproc(25号,.08锥度)、ProDesign R(25号,.06锥度)和Mtwo(25号,.06锥度)预备MB2根管。
  • 预备前后用micro-CT扫描评估根管偏移、中心定位能力、牙本质厚度和体积变化,并记录达到工作长度的时间。
  • 统计采用Kruskal-Wallis检验和Dunn多重比较,显著性水平5%。

主要发现

  • 三组间根管偏移和中心定位能力无显著差异(P > 0.05)。
  • ProDesign R(25号,.06锥度)组根管体积和去釉质体积显著低于Mtwo(25号,.06锥度)和Reciproc(25号,.08锥度)组(P < 0.05)。
  • Mtwo(25号,.06锥度)组和Reciproc(25号,.08锥度)组各检测到一例根穿孔。
  • ProDesign R(25号,.06锥度)达到工作长度所需时间显著长于Mtwo(25号,.06锥度)和Reciproc(25号,.08锥度)(P < 0.05)。

临床怎么用

  • 对于MB2根管预备,三种镍钛系统在根管偏移和中心定位方面表现相似,可根据临床需求选择。
  • 若需减少牙本质去除量,可考虑使用ProDesign R(25号,.06锥度),但需注意其操作时间较长。
  • 使用Mtwo(25号,.06锥度)或Reciproc(25号,.08锥度)时应注意根穿孔风险。

局限性

  • 离体牙研究,样本量较小(每组10颗),结果需临床进一步验证。
  • 仅评估了三种特定镍钛系统对MB2根管的预备效果,结论不能推广至其他系统或根管类型。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIM: To evaluate the influence of three engine-driven NiTi file systems manufactured from different NiTi alloys for the preparation of second mesiobuccal (MB2) canals in extracted maxillary first molars using a micro-computed tomographic (micro-CT) scanner. METHODOLOGY: Thirty maxillary molars with two canals in the mesiobuccal root were selected and randomly divided into three groups (n = 10): Reciproc [REC; size 25, .08 taper; VDW, Munich, Germany], ProDesign R [PDR; size 25, .06 taper; Easy, Belo Horizonte, Brazil] and Mtwo [MO; size 25, .06 taper; VDW, Munich, Germany]. Before and after root canal preparation of the MB2 canal, the teeth were scanned using a micro-CT to evaluate canal transportation, centring ability, dentine thickness and volume change. The working time to achieve working length was also evaluated. All parameters were compared statistically using the Kruskal-Wallis and Dunn test for multiple comparisons, with a significance level of 5%. RESULTS: There was no significant difference amongst the groups regarding canal transportation and centring ability (P > 0.05). However, the PDR size 25, .06 taper group had significantly lower canal volume and volume of dentine removal compared with a MO size 25, .06 taper and REC size 25, .08 taper (P < 0.05). A root perforation was detected in MO size 25, .06 taper and REC size 25, .08 taper groups, respectively. Regarding the working time, the PDR size 25, .06 taper required a significantly longer time to achieve working length than MO size 25, .06 taper and REC size 25, .08 taper (P < 0.05). CONCLUSIONS: All NiTi systems had similar canal transportation, centring ability and increase in apical volume after preparation of MB2 canals. However, the PDR size 25, .06 taper had less volume of dentine removal, absence of root canal perforation and required a longer time to accomplish the root canal preparation.

来源:Int Endod J,查看原文。版权归原作者所有。

引用

  1. Camargo EJ, Duarte MAH, Marques VAS, et al. The ability of three nickel-titanium mechanized systems to negotiate and shape MB2 canals in extracted maxillary first molars: a micro-computed tomographic study. Int Endod J. 2018. PMID: 30548555. doi:10.1111/iej.13056

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。