文献速递牙体牙髓病

上下往返速度对镍钛旋转器械根管中心定位能力及垂直力与扭矩的影响

Effect of Different Speeds of Up-and-down Motion on Canal Centering Ability and Vertical Force and Torque Generation of Nickel-titanium Rotary Instruments.
PubMed 文献 · J Endod · 2019-01-01

结果显示高速组中心定位能力最佳,但垂直力和扭矩倾向增大;X2和X3器械高速和/或中速组力与扭矩显著大于低速组。

要点

  • 高速上下往返(100 mm/min)时ProTaper Next中心定位能力最佳。
  • 速度增加使垂直力和顺时针扭矩倾向增大,X2和X3更明显。
  • X2器械在低速组和高速组分别有1根和2根折断。

核心结论

  • 上下往返速度影响ProTaper Next器械的根管中心定位能力和应力生成。
  • 高速组中心定位能力最佳,但倾向产生比中速和低速组更大的垂直力和扭矩。

研究设计与样本

  • 使用ProTaper Next X1、X2和X3器械,在自动根管预备与扭矩/力分析装置上以10、50、100 mm/min上下往返速度(低、中、高速组)预备。
  • 预备前后图像重叠,计算距根尖0-3 mm处的中心定位比率,并记录最大垂直力和扭矩。
  • 采用单因素方差分析和Tukey检验进行统计分析。

主要发现

  • 距根尖0、0.5、1和2 mm处,高速组中心定位比率最低(即偏差最小),其次为中速组和低速组(P < .05)。
  • 向下和向上力值随上下往返速度增加而倾向增大;X2和X3器械的高速和/或中速组显著大于低速组(P < .05)。
  • 所有器械的高速和/或中速组顺时针扭矩显著大于低速组(P < .05)。
  • X2器械在低速组折断1根,在高速组折断2根。

临床怎么用

  • 临床使用ProTaper Next时需权衡上下往返速度:高速可改善中心定位但增加力和扭矩。
  • 使用X2和X3器械时应注意速度增加带来的垂直力和扭矩升高及折断风险。

局限性

  • 研究采用模拟树脂根管块,非真实牙本质根管。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: This study was performed to evaluate how the speed of up-and-down motion affects the canal centering ability and torque/force generation of ProTaper Next rotary instruments (Dentsply Maillefer, Ballaigues, Switzerland). METHODS: Twenty-one simulated resin canal blocks with a J-shaped canal were prepared with ProTaper Next X1, X2, and X3 instruments using an original automated root canal instrumentation and torque/force analyzing device with up-and-down speed settings of 10, 50, and 100 mm/min (low-, medium-, and high-speed groups, respectively). Pre- and postinstrumentation images were superimposed, and centering ratios were calculated at 0-3 mm from the apex. The maximum vertical force and torque were also recorded. The results were statistically analyzed using 1-way analysis of variance and the Tukey test. RESULTS: At 0, 0.5, 1, and 2 mm from the apex, the high-speed group showed the lowest centering ratio (ie, least deviation) followed by the medium-speed and low-speed groups (P < .05). Force values (downward and upward) tended to increase as the up-and-down speed increased; with the X2 and X3 instruments, the high-speed and/or medium-speed groups generated significantly larger values than the low-speed group (P < .05). With all instruments, the high-speed and/or medium-speed groups generated significantly larger clockwise torque than the low-speed group (P < .05). One and 2 X2 instruments fractured in the low- and high-speed groups, respectively. CONCLUSIONS: The up-and-down speed affected the canal centering ability and stress generation of ProTaper Next instruments. The high-speed group showed the best centering ability but tended to generate larger vertical force and torque than the medium- and low-speed groups.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Maki K, Ebihara A, Kimura S, et al. Effect of Different Speeds of Up-and-down Motion on Canal Centering Ability and Vertical Force and Torque Generation of Nickel-titanium Rotary Instruments. J Endod. 2019. PMID: 30558799. doi:10.1016/j.joen.2018.10.002

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。