等离子喷涂氧化锆涂层在牙种植体中的应用研究
本研究采用等离子喷涂在纯钛种植体表面制备氧化锆涂层,检测其表面形貌、粗糙度与接触角,并将涂层种植体与纯钛种植体植入兔胫骨,于2、4、8、12周通过推出实验、扫描电镜、显微CT及硬组织切片评价骨整合。结果显示涂层种植体表面更利于成骨,12周推出力和骨-种植体结合率均显著优于纯钛组。
要点
- 氧化锆涂层种植体表面粗糙度1.6 µm、接触角54.6°,优于纯钛的0.6 µm和74.4°。
- 术后12周涂层组推出力(64.9±3.0)N高于对照组(50.4±2.9)N,差异有统计学意义。
- 术后12周涂层组BIC(54.7±3.6)%高于对照组(41.5±3.6)%,差异有统计学意义。
核心结论
- 氧化锆涂层钛种植体表面更适于成骨,且比表面光滑的纯钛种植体展现出更好的成骨能力,尤其在成骨早期阶段。
研究设计与样本
- 采用等离子喷涂法在光滑圆柱形纯钛种植体表面制备氧化锆涂层,检测表面形态、粗糙度及接触角。
- 将纯钛种植体(对照组)和氧化锆涂层钛种植体(涂层组)分别植入兔胫骨近骨骺端。
- 术后2、4、8、12周取材,每组每个时间点17只兔,共68只。
主要发现
- 氧化锆涂层种植体表面接触角(54.6°±1.8°)小于纯钛种植体(74.4°±3.6°)。
- 扫描电镜可见氧化锆涂层种植体表面有次微米级别及纳米级别孔隙。
- 术后12周涂层组和对照组推出力值分别为(64.9±3.0)和(50.4±2.9)N。
- 术后12周涂层组和对照组BIC分别为(54.7±3.6)%和(41.5±3.6)%,两组差异均有统计学意义(P<0.05)。
关键数值与推荐
- 氧化锆涂层种植体表面粗糙度为1.6 µm,纯钛种植体为0.6 µm。
- 氧化锆涂层种植体表面接触角为54.6°,纯钛种植体为74.4°。
- 术后12周推出力涂层组(64.9±3.0)N、对照组(50.4±2.9)N,差异有统计学意义(P<0.05)。
- 术后12周BIC涂层组(54.7±3.6)%、对照组(41.5±3.6)%,差异有统计学意义(P<0.05)。
临床怎么用
- 氧化锆涂层可能改善钛种植体表面的润湿性和粗糙度,从而促进早期骨整合。
- 动物实验提示涂层种植体在早期骨结合方面优于光滑纯钛种植体,但需进一步临床研究验证。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
Objective: To investigate the osseointegration of a novel coating-plasma-sprayed zirconia in dental implant. Methods: Zirconia coating on non-thread titanium implant was prepared using plasma spraying, the implant surface morphology, surface roughness and wettability were measured. In vivo, zirconia coated implants were inserted in rabbit tibia and animals were respectively sacrificed at 2, 4, 8 and 12 weeks after implantation. The bond strength between implant and bone was measured by push-out test. The osseointegration was observed by scanning electron microscopy (SEM), micro CT and histological analyses. Quantified parameters including removal torque, and bone-implant contact (BIC) percentage were calculated. Results: The surface roughness (1.6 µm) and wettability (54.6°) of zirconia coated implant was more suitable than those of titanium implant (0.6 µm and 74.4°) for osseointegration. At 12 weeks, the push-out value of zirconia coated implant and titanium implant were (64.9±3.0) and (50.4±2.9) N, and BIC value of these two groups were (54.7±3.6)% and (41.5±3.6)%. All these differences had statistical significance. Conclusions: The surface characters of zirconia coated implant were more suitable for osseointegration and present better osseointegration than smooth titanium implant in vivo, especially at early stage. 目的: 检测新型等离子喷涂氧化锆涂层钛种植体的骨整合能力,为其进一步临床应用提供参考。 方法: 采用等离子喷涂的方法在光滑圆柱形纯钛种植体表面制备氧化锆涂层,并检测其表面形态、粗糙度及表面接触角。将纯钛种植体(对照组)、氧化锆涂层钛种植体(涂层组)分别植入兔胫骨近骨骺端,术后2、4、8、12周分别取材(每组每个时间点17只兔,共68只),通过推出实验、扫描电镜、显微CT及硬组织切片的方法检测种植体的骨结合水平,并计算骨-种植体结合率(bone-implant contact,BIC)。 结果: 相比纯钛种植体(74.4°±3.6°),氧化锆涂层种植体的表面接触角(54.6°±1.8°)更小,扫描电镜下可见氧化锆涂层种植体表面有次微米级别及纳米级别孔隙。术后12周涂层组和对照组的推出力值分别为(64.9±3.0)和(50.4±2.9)N,BIC分别为(54.7±3.6)%和(41.5±3.6)%,两组差异均有统计学意义(P<0.05)。 结论: 氧化锆涂层钛种植体表面更适于成骨,且比表面光滑的纯钛种植体展现出更好的成骨能力,尤其在成骨早期阶段。.
引用
- Huang ZF, Wang ZF, Li CH, et al. [Application of plasma sprayed zirconia coating in dental implant: study in implant]. Zhonghua Kou Qiang Yi Xue Za Zhi. 2018. PMID: 29690698. doi:10.3760/cma.j.issn.1002-0098.2018.04.010
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。