文献速递牙体牙髓病

不同横截面镍钛旋转器械应力分布的有限元分析

Comparative Evaluation of Stress Distribution in Experimentally Designed Nickel-titanium Rotary Files with Varying Cross Sections: A Finite Element Analysis.
PubMed 文献 · J Endod · 2018-02-14

本研究用有限元分析比较5种横截面设计的镍钛旋转器械在45°弯曲模拟根管中的弯曲应力,包括单横截面CT、TR、TU及实验性组合设计CTU和UTC;结果显示CTU设计弯曲应力最小,CT设计根尖三分之一应力最大,各设计间差异有统计学意义。

要点

  • CTU组合横截面设计在45°弯曲根管中弯曲应力最小
  • CT单横截面设计在根尖三分之一处弯曲应力最大
  • 各镍钛器械设计间弯曲应力差异有统计学意义

核心结论

  • CTU设计的器械在45°弯曲模拟根管中较其他所有测试设计表现出最小的弯曲应力。

研究设计与样本

  • 研究采用有限元分析,建立45°弯曲模拟根管三维模型及5种横截面设计的镍钛器械模型。
  • 5组镍钛器械包括单横截面CT、TR、TU设计,以及实验性组合设计CTU和UTC。
  • 使用Kruskal-Wallis检验和Bonferroni校正的Mann-Whitney检验进行多重比较,P值<.05(95%)。

主要发现

  • 旋转器械最大弯曲应力见于CT设计的根尖三分之一处。
  • CTU设计的弯曲应力相对较小。
  • TU和TR设计在弯曲处显示相似的应力模式。
  • UTC设计在弯曲根管的根尖和中三分之一显示更大应力。
  • 所有器械设计间差异有统计学意义。

临床怎么用

  • 在45°弯曲根管中,CTU组合横截面设计可能有助于降低镍钛器械弯曲应力。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: Single cross-sectional nickel-titanium (NiTi) rotary instruments during continuous rotations are subjected to constant and variable stresses depending on the canal anatomy. This study was intended to create 2 new experimental, theoretic single-file designs with combinations of triple U (TU), triangle (TR), and convex triangle (CT) cross sections and to compare their bending stresses in simulated root canals with a single cross-sectional instrument using finite element analysis. METHODS: A 3-dimensional model of the simulated root canal with 45° curvature and NiTi files with 5 cross-sectional designs were created using Pro/ENGINEER Wildfire 4.0 software (PTC Inc, Needham, MA) and ANSYS software (version 17; ANSYS, Inc, Canonsburg, PA) for finite element analysis. The NiTi files of 3 groups had single cross-sectional shapes of CT, TR, and TU designs, and 2 experimental groups had a CT, TR, and TU (CTU) design and a TU, TR, and CT (UTC) design. The file was rotated in simulated root canals to analyze the bending stress, and the von Mises stress value for every file was recorded in MPa. Statistical analysis was performed using the Kruskal-Wallis test and the Bonferroni-adjusted Mann-Whitney test for multiple pair-wise comparison with a P value <.05 (95 %). RESULTS: The maximum bending stress of the rotary file was observed in the apical third of the CT design, whereas comparatively less stress was recorded in the CTU design. The TU and TR designs showed a similar stress pattern at the curvature, whereas the UTC design showed greater stress in the apical and middle thirds of the file in curved canals. All the file designs showed a statistically significant difference. CONCLUSIONS: The CTU designed instruments showed the least bending stress on a 45° angulated simulated root canal when compared with all the other tested designs.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Basheer Ahamed SB, Vanajassun PP, Rajkumar K, et al. Comparative Evaluation of Stress Distribution in Experimentally Designed Nickel-titanium Rotary Files with Varying Cross Sections: A Finite Element Analysis. J Endod. 2018. PMID: 29426643. doi:10.1016/j.joen.2017.12.013

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。