文献速递牙体牙髓病口腔颌面外科

计算机辅助设计与制造导板在厚颊侧骨板下颌磨牙根尖手术中的应用

Computer-aided Design/Computer-aided Manufacturing-guided Endodontic Surgery: Guided Osteotomy and Apex Localization in a Mandibular Molar with a Thick Buccal Bone Plate.
PubMed 文献 · J Endod · 2018-01-19

本报告描述一例57岁女性下颌磨牙因厚颊侧骨板导致根尖手术困难,采用CAD/CAM导板引导截骨和根尖定位。通过CBCT与模型扫描数据叠加设计锚钉 targeting 近中根尖,3D打印手术导板,术中应用导板最小化截骨范围并精准定位根尖,术后无并发症。

要点

  • CAD/CAM导板可最小化厚颊侧骨板磨牙的截骨范围。
  • 导板有助于精准定位根尖,减少手术创伤。
  • 术后无并发症,导板适用于复杂根尖手术病例。

核心结论

  • CAD/CAM引导的手术导板在复杂根尖手术中有助于最小化截骨并精准定位根尖,术后无并发症。

研究设计与样本

  • 病例报告:57岁女性,19号牙既往治疗史,诊断为症状性根尖周炎,非手术再治疗2年后疼痛复发,CBCT确认根尖病变,计划行近中根根尖手术。

主要发现

  • 应用3D打印手术导板后,截骨范围最小化,根尖定位精准,术后无并发症。

临床怎么用

  • 对于厚颊侧骨板的复杂根尖手术病例,可考虑使用CAD/CAM导板辅助截骨和根尖定位。

局限性

  • 仅为单例病例报告,结论推广需谨慎。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

A mandibular molar with a thick buccal bone plate is a challenging problem in endodontic surgery despite the increase in the success rate of endodontic surgery nowadays. This report describes the application of a surgical template to guide osteotomy and facilitate apex localization in a mandibular molar with a thick buccal bone plate. A 57-year-old woman visited the authors' clinic for pain in tooth 19 and was diagnosed with symptomatic apical periodontitis in this previously treated tooth. Nonsurgical retreatment was performed; however, 2 years later, the patient reported pain in the same tooth. A periapical lesion was confirmed using cone-beam computed tomographic (CBCT) imaging, and endodontic surgery on the mesial root of tooth 19 was planned. After CBCT imaging and cast scan data were transferred to implant surgical planning software, the data were superimposed. In the superimposed model, an anchor pin was designed to target the mesial root apex of tooth 19. The surgical template was then printed using a 3-dimensional printer. Endodontic microsurgery included application of this printed surgical template. A computer-aided design/computer-aided manufacturing (CAD/CAM)-guided surgical template minimized the extent of osteotomy and enabled precise targeting of the apex in this case. There were no postoperative complications. A CAD/CAM-guided surgical template is useful in endodontic surgery for complicated cases.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Ahn SY, Kim NH, Kim S, et al. Computer-aided Design/Computer-aided Manufacturing-guided Endodontic Surgery: Guided Osteotomy and Apex Localization in a Mandibular Molar with a Thick Buccal Bone Plate. J Endod. 2018. PMID: 29358006. doi:10.1016/j.joen.2017.12.009

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。