文献速递牙体牙髓病

三种镍钛疏通锉在S形双弯人工根管中的循环疲劳抗力比较

Cyclic fatigue resistance of R-Pilot, HyFlex EDM and PathFile nickel-titanium glide path files in artificial canals with double (S-shaped) curvature.
PubMed 文献 · Int Endod J · 2017-09-18

研究比较R-Pilot、HyFlex EDM与PathFile三种镍钛疏通锉在S形双弯人工根管中的循环疲劳抗力。结果显示R-Pilot的NCF最大,其次为HyFlex EDM和PathFile,两个弯曲处差异均有统计学意义(P < 0.05)。

要点

  • R-Pilot在S形双弯根管中循环疲劳抗力最高,HyFlex EDM次之,PathFile最低。
  • 所有锉均先在根尖弯曲处折断,后在冠方弯曲处折断。
  • R-Pilot采用往复运动,其抗循环疲劳性能优于两种连续旋转锉。

核心结论

  • 在S形双弯人工根管中,R-Pilot镍钛疏通锉(往复运动)的循环疲劳抗力在三种测试锉中最大。

主要发现

  • 所有锉均先在根尖弯曲处折断,后在冠方弯曲处折断。
  • 根尖弯曲和冠方弯曲处,R-Pilot的NCF均最大,其次为HyFlex EDM,PathFile最小(P < 0.05)。
  • 每组取2支折断锉(共6支)进行SEM观察以确定折断模式。

关键数值与推荐

  • NCF通过转速乘以折断时间计算。
  • 断端长度(FL)用数字千分尺测量。
  • 统计分析采用单因素方差分析、Tamhane事后检验和Kruskal-Wallis检验,显著性水平设为5%。

临床怎么用

  • 在S形双弯根管预备中,如需较高抗循环疲劳性能的疏通锉,可优先考虑R-Pilot。
  • 使用镍钛疏通锉时应注意根尖弯曲处为最先发生疲劳折断的部位。

局限性

  • 研究使用人工S形双弯根管,非真实根管解剖结构。
  • 仅为静态循环疲劳测试,未模拟动态临床运动。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIM: To examine the cyclic fatigue resistances of R-Pilot, HyFlex EDM and PathFile NiTi glide path files in S-shaped artificial canals. METHODOLOGY: Twenty R-Pilot (12.5/.04), 20 HyFlex EDM (10/.05) and 20 PathFile (19/.02) single-file glide path files were included. Sixty files (n: 20/each) were subjected to static cyclic fatigue testing using double-curved canals until fracture occurred (TF). The number of cycles to fracture (NCF) was calculated by multiplying the rpm value by the TF. The length of the fractured fragment (FL) was determined by a digital microcaliper. Six samples of fractured files (n: 2/each) were examined by SEM to determine the fracture mode. The NCF and the FL data were analysed using one-way anova, post hoc Tamhane and Kruskal-Wallis tests using SPPS 21 software. The significance level was set at 5%. RESULTS: In the double-curved canal, all the files fractured first in the apical curvature and then in the coronal curvature. The NCF values revealed that the R-Pilot had the greatest cyclic fatigue resistance, followed by the HyFlex EDM and PathFile in both the apical and coronal curvatures (P < 0.05). CONCLUSIONS: R-Pilot NiTi glide path files, used in a reciprocating motion, had the greatest cyclic fatigue resistance amongst the tested NiTi glide path files in an artificial S-shaped canal.

来源:Int Endod J,查看原文。版权归原作者所有。

引用

  1. Uslu G, Özyürek T, Yılmaz K, et al. Cyclic fatigue resistance of R-Pilot, HyFlex EDM and PathFile nickel-titanium glide path files in artificial canals with double (S-shaped) curvature. Int Endod J. 2017. PMID: 28856692. doi:10.1111/iej.12846

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。