文献速递牙体牙髓病

不同往复旋转模式下镍钛器械根管预备的扭矩与垂直力分析

Dynamic Torque and Vertical Force Analysis during Nickel-titanium Rotary Root Canal Preparation with Different Modes of Reciprocal Rotation.
PubMed 文献 · J Endod · 2017-07-20

本研究用定制自动化装置在树脂模拟根管中比较扭矩敏感型往复、时间依赖型往复与连续旋转三种模式下TF Adaptive器械的扭矩和根尖力。结果显示两种往复模式的最大扭矩均显著小于连续旋转,时间依赖型往复的最大向上根尖力也显著小于连续旋转。提示往复旋转可能减少螺纹拧入力所致的应力。

要点

  • 两种往复旋转的最大扭矩均显著低于连续旋转。
  • 时间依赖型往复的最大向上根尖力显著小于连续旋转。
  • 记录到间断出现的向上根尖力和顺时针扭矩,反映拧入力的产生与释放。

核心结论

  • 在TF Adaptive器械的實驗条件下,扭矩敏感型与时间依赖型往复旋转产生的最大扭矩均显著低于连续旋转,可能有利于减少拧入力所致应力。

研究设计与样本

  • 采用定制自动化根管预备与扭矩/力分析装置,在树脂块模拟根管中预备并监测扭矩和根尖力。
  • 实验分三组(每组n=7):扭矩敏感型往复旋转配扭矩敏感垂直运动(TqR)、时间依赖型往复旋转配时间依赖垂直运动(TmR)、连续旋转配时间依赖垂直运动(CR)。
  • 使用TF Adaptive SM1和SM2镍钛锉预备,测量SM2预备过程中的扭矩和根尖力。
  • 均值与最大值采用单因素方差分析和Tukey检验(α=0.05)。

主要发现

  • 记录显示向上根尖力和顺时针扭矩呈间歇性升高,表明拧入力的产生与释放。
  • TmR组最大向上根尖力显著小于CR组(P < .05)。
  • TqR组和TmR组顺时针及逆时针方向的最大扭矩均显著小于CR组(P < .05)。

临床怎么用

  • 在类似树脂模拟根管条件下,选用往复旋转模式可能降低最大扭矩和拧入力相关应力。
  • 时间依赖型往复旋转在降低最大向上根尖力方面可能优于连续旋转。

局限性

  • 实验在树脂块模拟根管中进行,非真实牙本质根管。
  • 仅测试TF Adaptive SM1和SM2器械,结论外推需谨慎。
  • 样本量每组7个,统计效能有限。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The purpose of the present study was to compare 2 modes of reciprocal movement (torque-sensitive and time-dependent reciprocal rotation) with continuous rotation in terms of torque and apical force generation during nickel-titanium rotary root canal instrumentation. METHODS: A custom-made automated root canal instrumentation and torque/force analyzing device was used to prepare simulated canals in resin blocks and monitor the torque and apical force generated in the blocks during preparation. Experimental groups (n = 7, each) consisted of (1) torque-sensitive reciprocal rotation with torque-sensitive vertical movement (group TqR), (2) time-dependent reciprocal rotation with time-dependent vertical movement (group TmR), and (3) continuous rotation with time-dependent vertical movement (group CR). The canals were instrumented with TF Adaptive SM1 and SM2 rotary files (SybronEndo, Orange, CA), and the torque and apical force were measured during instrumentation with SM2. The mean and maximum torque and apical force values were statistically analyzed using 1-way analysis of variance and the Tukey test (α = 0.05). RESULTS: The recordings showed intermittent increases of upward apical force and clockwise torque, indicating the generation and release of screw-in forces. The maximum upward apical force values in group TmR were significantly smaller than those in group CR (P < .05). The maximum torque values in clockwise and counterclockwise directions in groups TqR and TmR were significantly smaller than those in group CR (P < .05). CONCLUSIONS: Under the present experimental conditions using TF Adaptive instruments, both torque-sensitive and time-dependent reciprocal rotation generated significantly lower maximum torque and may have advantages in reducing stress generation caused by screw-in forces when compared with continuous rotation.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Tokita D, Ebihara A, Nishijo M, et al. Dynamic Torque and Vertical Force Analysis during Nickel-titanium Rotary Root Canal Preparation with Different Modes of Reciprocal Rotation. J Endod. 2017. PMID: 28735792. doi:10.1016/j.joen.2017.05.010

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。