文献速递口腔修复与种植口腔正畸

植入角度对负载微螺钉稳定性的影响

[Effect of inserted angle on the stability of loaded microscrews].
PubMed 文献 · Zhonghua Kou Qiang Yi Xue Za Zhi · 2017-01-01

在12只比格犬下颌第一磨牙与第三前磨牙间牙根间隔区以30°、50°、70°和90°四种角度植入48枚微螺钉,并即刻负载2 N力8周。结果显示50°组最大拔出力最大,70°组骨-种植体接触率最大,30°组两项指标均最低(P<0.05);50°和70°植入角度有利于微螺钉稳定性。

要点

  • 50°组最大拔出力为(385±23)N,高于30°组的(198±16)N(P<0.05)。
  • 70°组骨-种植体接触率为(59.1±6.0)%,高于30°组的(30.2±3.2)%(P<0.05)。
  • 50°和70°植入角度有利于微螺钉稳定性。

核心结论

  • 50°和70°植入角度有利于微螺钉的稳定性。

研究设计与样本

  • 在12只比格犬下颌第一磨牙与第三前磨牙间牙根间隔区以30°、50°、70°和90°四种角度植入48枚微螺钉,并即刻负载2 N力8周。

主要发现

  • 最大拔出力最大值为(385±23)N,见于50°组;最小值为(198±16)N,见于30°组(P<0.05)。
  • 骨-种植体接触率最大值为(59.1±6.0)%,见于70°组;最小值为(30.2±3.2)%,见于30°组(P<0.05)。
  • 组织形态学观察显示不同角度样本微螺钉周围区域存在不同程度的骨改建。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

Objective: To evaluate the effect of different insertion angles on the osseointegration of loaded microscrews in beagle jaws. Methods: Forty-eight microscrews were inserted at four different angles (30°, 50°, 70° and 90°) into the interradicular zones between the mandibular first molar and third premolar in twelve beagles and the microscrews had been loaded with a force of 2 N immediately for 8 weeks. After microscrew-bone specimens fixed, the maximum output value (Fmax) of pull-out test was recorded and the histomorphological changes of hard tissue were observed. The bone-implant contact (BIC%) was quantitatively analyzed and the osseointegration of microscrew-bone interface was comprehensively evaluated. Results: Both Fmax and BIC% values of microscrews were influenced by the insertion angles. The maximum value of Fmax was (385±23) N in the group with 50° angle, and the minimum value was (198±16) N in the group with 30° angle(P <0.05). The maximum value of BIC% was (59.1±6.0)% in the group with 70° angle, and the minimum value was (30.2±3.2)% in the group with 30° angle (P <0.05). Histomorphology observation revealed that in peri-screws region, the various degree of bone remodeling was found in different angle samples. Conclusions: The insertion angles (50°and 70°) were favorable to the stability of the microscrew.

来源:Zhonghua Kou Qiang Yi Xue Za Zhi,查看原文。版权归原作者所有。

引用

  1. Shao P, Xu ZR, Zhao LX, et al. [Effect of inserted angle on the stability of loaded microscrews]. Zhonghua Kou Qiang Yi Xue Za Zhi. 2017. PMID: 28072993. doi:10.3760/cma.j.issn.1002-0098.2017.01.008

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。