不同体素大小和视野的锥形束CT图像、根尖片及根尖定位仪测量牙髓工作长度的比较:一项离体研究
本研究在30颗离体人下颌前磨牙上,比较电子根尖定位仪、根尖片及不同体素大小和视野的锥形束CT测量工作长度的准确性,以电子数显卡尺直接测量为金标准。结果显示不同方法间与金标准的平均差异有显著差异,根尖片操作者内与操作者间无显著差异,而锥形束CT图像有显著差异,结论认为不同视野的锥形束CT扫描可用于工作长度测量。
要点
- 研究纳入30颗离体人下颌前磨牙,比较5种影像方法与电子根尖定位仪的工作长度测量。
- 根尖片操作者内与操作者间无显著差异(P > .05,Gage R&R值<30%)。
- 锥形束CT图像操作者内与操作者间有显著差异(P < .05,Gage R&R值>30%)。
核心结论
- 本研究表明,不同视野的现有锥形束CT扫描可用于工作长度测量。
研究设计与样本
- 离体研究,使用30颗离体人下颌前磨牙,以电子数显卡尺直接测量为金标准。
- 电子工作长度测量使用电子根尖定位仪(Root ZX;J Morita Corp,京都,日本)。
- 获取5组图像:视野40×40 mm、体素0.080 mm³(FOV40);视野60×60 mm、体素0.125 mm³(FOV60);视野80×80 mm、体素0.160 mm³(FOV80);视野100×100 mm、体素0.250 mm³(FOV100);以及根尖数字X线摄影。
- 数据采用双因素方差分析,显著性水平设定为P < .05。
主要发现
- 根尖片操作者内与操作者间无显著差异(P > .05,Gage R&R值<30%)。
- 锥形束CT图像操作者内与操作者间有显著差异(P < .05,Gage R&R值>30%)。
- 各方法与金标准的平均差异有显著差异(P < .05)。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The aim of this study was to evaluate the accuracy of working length determination by using an electronic apex locator, periapical radiography, and cone-beam computed tomographic (CBCT) imaging obtained at different voxel sizes and field of views (FOVs) in extracted human teeth. METHODS: Thirty extracted human mandibular premolar teeth were used. The electronic working length measurements were performed by using an electronic apex locator (Root ZX; J Morita Corp, Kyoto, Japan). Five different image sets were obtained as follows: (1) CBCT imaging: 40 × 40 mm FOV, 0.080 mm3 (FOV40); (2) CBCT imaging: 60 × 60 mm FOV, 0.125 mm3 (FOV60); (3) CBCT imaging: 80 × 80 mm FOV, 0.160 mm3 (FOV80); (4) CBCT imaging: 100 × 100 mm FOV, 0.250 mm3 (FOV100); and (5) periapical digital radiography. Direct measurements performed with an electronic digital caliper were considered as the gold standard and compared with the electronic apex locator, CBCT, and periapical image measurements. Data were analyzed using a 2-way analysis of variance test. Significance level was set at P < .05. RESULTS: There was no significant difference between or within operators in intraoral radiographs (P > .05 and the Gage R&R value was <30%). There were significant differences between and within operators for CBCT images (P < .05 and Gage R&R value was >30%). There were significant differences in the methods in terms of mean differences from the gold standard (P < .05). CONCLUSIONS: This study showed that available CBCT scans with different FOVs can be used for working length measurement.
引用
- Yılmaz F, Kamburoğlu K, Şenel B, et al. Endodontic Working Length Measurement Using Cone-beam Computed Tomographic Images Obtained at Different Voxel Sizes and Field of Views, Periapical Radiography, and Apex Locator: A Comparative Ex Vivo Study. J Endod. 2017. PMID: 27986097. doi:10.1016/j.joen.2016.09.019
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。