文献速递牙体牙髓病

下颌切牙根管形态测量及其对器械尺寸-锥度选择的启示

Morphometric Mapping of Mandibular Incisor Root Canals and Its Implications for Instrument Size-taper Selection.
PubMed 文献 · J Endod · 2026-03-24

结果显示根管解剖不对称,传统镍钛器械与大径的对应性有限,尤其在中冠三分之一。

要点

  • 下颌切牙根管在中冠三分之一呈明显不对称,大径增宽更显著。
  • 镍钛器械与小径的对应性取决于锥度,大锥度需配合小尖端尺寸达80%阈值。
  • 所有器械尺寸和锥度与大径的对应性均有限,全长无器械达80%。

核心结论

  • 下颌切牙根管解剖呈显著不对称,尤其在中冠三分之一,导致传统镍钛器械与大径对应性有限。

主要发现

  • 根管小径和大径向冠方逐渐增大,大径从中三分之一向冠方增宽更明显。
  • 根尖区以圆形根管为主,中冠三分之一以长椭圆形根管最普遍,扁平根管主要位于距根尖6至7 mm处。
  • 镍钛器械与小径的对应性强烈依赖锥度,较小尖端尺寸需较大锥度才能达到80%阈值。
  • 所有器械尺寸和锥度与大径的对应性均明显有限,全长无器械达到≥80%对应。
  • 小径与大径之间相关性弱,表明根管尺寸不成比例增大。

关键数值与推荐

  • 以80%频率阈值判定根管尺寸与器械尺寸的有意义对应。
  • 截面按长宽比分类为圆形、长椭圆形或扁平。
  • 小径与大径关联用Pearson相关系数评估。

临床怎么用

  • 选择下颌切牙镍钛器械时需考虑根管中冠三分之一的不对称性,避免仅依据小径选器械。
  • 对大径对应性有限,临床预备时应注意传统器械可能无法充分覆盖根管大径区域。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: This study aimed to characterize the morphology of mandibular incisor root canals and to evaluate their correspondence with commonly used nickel-titanium (NiTi) instruments. METHODS: One hundred extracted human mandibular incisors were scanned using high-resolution micro-computed tomography. Minor and major canal diameters and aspect ratios were measured at 1-mm intervals from the apical foramen to 10 mm coronally. Canal cross-sections were classified as round, long-oval, or flat based on aspect ratio. A supplementary analysis determined the percentage frequency of canals with diameters equal to or smaller than a wide range of size-taper combinations of constant-taper NiTi instruments. An 80% frequency threshold was applied to identify meaningful correspondence between canal dimensions and instrument sizes. Descriptive statistics were calculated, and the association between major and minor diameters was assessed using Pearson's correlation coefficient. RESULTS: Both minor and major canal diameters increased progressively in the coronal direction, although enlargement of the major diameter was more pronounced from the middle third coronally. Round canals predominated in the apical region, whereas long-oval canals were most prevalent in the middle and coronal thirds; flat canals occurred mainly between 6 and 7 mm from the apex. Correspondence between NiTi instruments and the minor canal diameter depended strongly on instrument taper, with larger tapers required for smaller tip sizes to reach the 80% threshold. In contrast, correspondence with the major canal diameter was markedly limited across all instrument sizes and tapers, with no instrument achieving ≥80% correspondence along the entire root length. The correlation between minor and major canal diameters was weak, indicating disproportionate enlargement of canal dimensions. CONCLUSIONS: Mandibular incisors present pronounced anatomical asymmetry, particularly in the middle and coronal thirds, resulting in limited correspondence between conventional NiTi instruments and the major canal diameter.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Lima CO, Silva EJNL, Maciel LV, et al. Morphometric Mapping of Mandibular Incisor Root Canals and Its Implications for Instrument Size-taper Selection. J Endod. 2026. PMID: 41887502. doi:10.1016/j.joen.2026.03.009

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。