文献速递口腔修复与种植

不同壳厚度与横弓杆对3D打印空心牙颌模型打印精度及上架后尺寸稳定性的影响

Printing accuracy and post-mounting dimensional stability of 3D-printed hollow dental models with varying shell thicknesses and cross-arch bars.
PubMed 文献 · J Dent · 2025-11-14

本体外研究设计四种上颌模型:1mm或4mm壳厚、有无横弓杆,每组数字光处理3D打印10个,比较打印前扫描与CAD文件评估打印精度、上架石膏后扫描评估尺寸稳定性。壳厚与横弓杆均显著影响真实度和上架后稳定性(P<.05),4mm壳厚带横弓杆组偏差最小、精度最高,1mm无杆组偏差最大。

要点

  • 壳厚与横弓杆显著影响3D打印空心牙颌模型的真实度和上架后稳定性。
  • 4mm壳厚带横弓杆组偏差最小、精度最高;1mm无杆组线性偏差最大。
  • 石膏凝固膨胀可致模型形变,薄壁无加强模型风险最高。

核心结论

  • 壳厚和加强结构显著影响3D打印空心牙颌模型的真实度与稳定性,较厚壳厚带横弓杆者精度和稳定性最高,支持用于需上架架的口腔修复应用。

研究设计与样本

  • 体外研究,设计四种上颌模型:1mm壳厚带杆(T1-B)、1mm无杆(T1-NB)、4mm带杆(T4-B)、4mm无杆(T4-NB),数字光处理3D打印,每组n=10。

主要发现

  • 壳厚与横弓杆均显著影响真实度和上架后稳定性(p<.05)。
  • T1-NB组打印精度线性偏差最大为899.2 µm,上架后稳定性线性偏差最大为190.2 µm。
  • T4-B组偏差最小、精度最高;石膏凝固膨胀引入可测量偏差,在T1-NB组最明显。

关键数值与推荐

  • 打印精度以打印前扫描与原始CAD文件比较评估,上架后稳定性以上架后与上架前扫描比较评估。
  • 偏差用表面分析(均方根)和线性测量量化,数据采用非参数检验或稳健双因素方差分析(α=.05)。

临床怎么用

  • 使用3D打印空心模型时,优化模型底座设计对保证打印精度及上架后尺寸稳定性至关重要。
  • 足够壳厚与加强结构可确保精度,薄壁无加强模型有石膏膨胀致形变风险,可能影响修复治疗结果。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: This in vitro study aimed to evaluate the impact of shell thickness and the presence of a cross-arch stabilizing bar on the dimensional accuracy of three-dimensional (3D) printed hollow dental models, assessing both printing accuracy and post-mounting dimensional stability. METHODS: Four types of maxillary models were designed: 1-mm shell with bar (T1-B), 1-mm shell without bar (T1-NB), 4-mm shell with bar (T4-B), and 4-mm shell without bar (T4-NB). Models were fabricated using a digital light processing 3D printer (n = 10 per group). All specimens were scanned before (pre-mounting) and after being filled with Type II dental plaster (post-mounting). Printing accuracy was assessed by comparing pre-mounting scans to the original computer-aided design files, and post-mounting stability was assessed by comparing post-mounting to pre-mounting scans. Deviations were quantified using surface analysis (root mean square) and linear measurements. Data were analyzed using either nonparametric tests or a robust two-way analysis of variance (α = .05). RESULTS: Both shell thickness and the cross-arch bar significantly affected trueness and post-mounting stability (p < .05). The T1-NB group consistently showed the largest deviations for both printing accuracy (linear: 899.2 µm) and post-mounting stability (linear: 190.2 µm). The T4-B group demonstrated the smallest deviations and highest accuracy. The setting expansion of the plaster introduced measurable deviations, which were most pronounced in the T1-NB group. CONCLUSIONS: Shell thickness and reinforcement significantly affected the trueness and stability of 3D-printed hollow dental models. Thicker shells with a cross-arch bar demonstrated the highest accuracy and stability, supporting their use in prosthodontic applications requiring articulator mounting. CLINICAL SIGNIFICANCE: Optimizing model base design is critical when 3D-printed hollow models are used, not only for ensuring printing accuracy but also for maintaining dimensional stability after articulator mounting. Adequate shell thickness and reinforcement ensure accuracy, whereas thin, unreinforced models risk distortion from plaster expansion, potentially compromising prosthodontic treatment outcomes.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Wan Q, Riera C, Tran TT, et al. Printing accuracy and post-mounting dimensional stability of 3D-printed hollow dental models with varying shell thicknesses and cross-arch bars. J Dent. 2025. PMID: 41242651. doi:10.1016/j.jdent.2025.106234

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。