3D打印临时与永久牙科树脂的单体组成及析出的比较LC-MS分析
本研究采用非靶向和靶向LC-MS比较四种商用3D打印树脂复合材料的化学组成及在人工唾液中的残余单体析出。非靶向分析检测到4125个化学特征,筛选出39个高置信度树脂衍生化合物;定量分析显示不同材料间单体析出谱差异显著,Saremco总体析出最低,提示需材料特异性生物相容性测试。
要点
- 3D打印牙科树脂的化学组成和单体析出具有高度材料特异性。
- 永久冠树脂间差异明显,需针对具体材料进行生物相容性测试。
- Saremco监测的单体析出浓度总体最低,但需结合临床选择。
核心结论
- 3D打印牙科树脂的化学组成和单体析出具有高度材料特异性。
- 永久冠树脂间的显著变异性强调需进行材料特异性生物相容性测试以确保长期临床安全。
研究设计与样本
- 研究分析了两种临时树脂(Temporary CB、NextDent C&B MFH)和两种永久3D打印树脂(Saremco print CrownTec、VarseoSmile Crown plus)。
- 未聚合树脂进行非靶向LC-MS组成筛查;聚合样本在人工唾液(37 °C,72 h)中浸泡后,用靶向定量LC-MS定量HEMA、TEGDMA、UDMA和Bis-EMA的析出。
主要发现
- 非靶向分析检测到4125个化学特征,筛选出39个高置信度树脂衍生化合物,主要为单体及衍生物,部分为光引发剂和添加剂。
- 永久树脂Saremco和VarseoSmile的化合物多样性最高。
- Bis-EMA在Temporary CB、Saremco和VarseoSmile中占主导,UDMA在NextDent、Saremco和VarseoSmile中丰度最高。
- Temporary CB和VarseoSmile的Bis-EMA析出最高,NextDent的HEMA和UDMA析出最高,VarseoSmile的TEGDMA析出最高。
- Saremco监测的所有单体析出浓度总体最低。
临床怎么用
- 临床选择3D打印树脂时需考虑材料特异性单体析出差异,可能影响患者安全和修复体耐久性。
- 建议对具体材料进行针对性的生物相容性测试。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: This study aimed to comparatively characterize the chemical composition of four commercial 3D-printed resin composites and quantify residual monomer elution profiles relevant to provisional and permanent fixed restorations. METHODS: Two provisional resins (Temporary CB, Formlabs and NextDent C&B MFH) and two permanent 3D-printed resins (Saremco print CrownTec and VarseoSmile Crown plus) were analyzed. Unpolymerized resins underwent untargeted liquid chromatography-mass spectrometry (LC-MS) for compositional screening. Polymerized specimens were immersed in artificial saliva (37 °C, 72 h), followed by targeted quantitative LC-MS to quantify eluted residual monomers using certified standards calibration curves for HEMA, TEGDMA, UDMA, and Bis-EMA. RESULTS: Untargeted analysis detected 4125 chemical features, refined to 39 high-confidence resin-derived compounds across four 3D-printed resin composites. These were mainly monomers and derivatives, with some photoinitiators and additives. Compound diversity varied by material, with permanent Saremco and VarseoSmile showing the greatest variety. Bis-EMA predominated in Temporary CB, Saremco, and VarseoSmile, while UDMA was most abundant in NextDent, Saremco, and VarseoSmile. Quantitative analysis of monomer elution revealed that Temporary CB and VarseoSmile released the highest levels of Bis-EMA, NextDent showed the greatest elution of HEMA and UDMA, and VarseoSmile had the highest TEGDMA release. Saremco generally exhibited the lowest concentrations of all monitored monomers. These results demonstrate substantial variability in both composition and monomer elution profiles among commercial 3D-printed dental resins. CONCLUSIONS: Chemical composition and monomer elution in 3D-printed dental resins are highly material-specific. The marked variability, especially among permanent crown resins, underscores the need for material-specific biocompatibility testing to ensure long-term clinical safety. CLINICAL SIGNIFICANCE: Material-specific differences in monomer elutions from 3D-printed dental resins may affect patient safety and restoration durability, underscoring the need for careful material selection and targeted biocompatibility testing in clinical practice.
引用
- Prawatvatchara W, Intarak N, Thaweesapphithak S, et al. Comparative LC-MS analysis of monomer composition and elution from provisional and permanent 3D-printed dental resins. J Dent. 2025. PMID: 41276065. doi:10.1016/j.jdent.2025.106262
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。