文献速递口腔修复与种植口腔颌面外科

3D打印羟基磷灰石块联合牙种植体在下颌骨增量中的骨结合实验研究

Dental Implant Osseointegration Following Mandibular Augmentation Using 3D Printed Hydroxyapatite Blocks. An Experimental In Vivo Study.
PubMed 文献 · Clin Oral Implants Res · 2025-10-11

在4只雌性Göttingen小型猪双侧下颌行gyroid多孔3D打印羟基磷灰石(3DHA)块增量,愈合8或12周后植入种植体,再愈合12周取材行组织学与组织形态学分析。3DHA块新骨形成39.17%,平均骨增量4.73 mm,种植体在3DHA内与自体骨内骨-种植体接触率(BIC)分别为42.79%与34.17%,两个愈合期无显著差异。

要点

  • gyroid多孔3DHA块可用螺钉固定,经其植入种植体可获得良好初期稳定性
  • 3DHA块内新骨形成39.17%,平均骨增量4.73 mm
  • 3DHA内与自体骨内BIC相近(42.79% vs. 34.17%)

核心结论

  • 3DHA块与牙种植体均显示良好骨结合,骨增量显著,有望用于大范围复杂牙槽嵴增量。
  • 作者称这是首个在动物研究中评估3D打印骨替代材料联合牙种植体的研究。

研究设计与样本

  • 实验性体内动物研究,在4只雌性Göttingen小型猪双侧下颌行gyroid-3DHA块侧向骨增量。
  • 愈合8或12周后于每个3DHA块内植入1枚牙种植体,再经12周愈合后取材行组织学与组织形态学分析。
  • 评估指标包括新骨形成、3DHA整合、总骨增量与骨-种植体接触率(BIC)。

主要发现

  • 3DHA块新骨形成为39.17%,平均骨增量4.73 mm。
  • 种植体在3DHA内BIC为42.79%,在自体骨内为34.17%。
  • 8周与12周两个愈合期之间未发现显著差异。

关键数值与推荐

  • 3DHA块新骨形成39.17%,平均骨增量4.73 mm。
  • 种植体BIC:3DHA内42.79%,自体骨内34.17%。

临床怎么用

  • 对需大范围下颌骨增量的病例,3DHA块可考虑作为骨替代材料,并可经其常规备洞植入种植体。
  • 术中可用螺钉固定3DHA块,种植体可获得良好初期稳定性。

局限性

  • 样本量小,仅4只动物,结论需更大样本验证。
  • 为动物实验,尚不能直接外推至临床患者。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: To evaluate the use and osseointegration of dental implants in combination with 3D-printed hydroxyapatite (3DHA) blocks featuring gyroid porosity for large mandibular bone augmentation. METHODS: Mandibular lateral bone augmentation with gyroid-3DHA blocks was performed bilaterally on four female Göttingen minipigs. After 8 or 12 weeks of healing, a dental implant was placed into each 3DHA block. Following an additional 12-week healing period, the augmented sites (including 3DHA blocks and dental implants) were harvested for histological and histomorphometric analysis, assessing new bone formation, 3DHA integration, total bone gain, and bone-to-implant contact (BIC). RESULTS: Gyroid-3DHA blocks were easily fixated with screws. Dental implants were placed through the 3DHA blocks with a standard drilling procedure, and good primary stability was achieved. 3DHA blocks demonstrated good osseointegration with 39.17% of new bone and a significant bone gain of 4.73 mm on average. Dental implants showed comparable BIC within the 3DHA and into the native bone (42.79% vs. 34.17%). No significant difference was found between the healing periods. CONCLUSION: This is the first study to evaluate a 3D-printed bone substitute in combination with a dental implant in an animal study. Gyroid-3DHA blocks and dental implants demonstrated good osseointegration, and the bone augmentation was significant, making it a promising material for large and complex alveolar ridge augmentations.

来源:Clin Oral Implants Res,查看原文。版权归原作者所有。

引用

  1. Systermans S, Ronsmans C, Nolens G, et al. Dental Implant Osseointegration Following Mandibular Augmentation Using 3D Printed Hydroxyapatite Blocks. An Experimental In Vivo Study. Clin Oral Implants Res. 2025. PMID: 41074904. doi:10.1111/clr.70056

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。