新型3D打印手术减压装置促进大型根尖周病变愈合:一例病例报告
本文报告一例21岁男性,右上前牙根管治疗后出现累及鼻腭管及颊舌侧皮质骨穿孔的大型根尖周病变。采用CBCT与数字软件设计并3D打印定制减压装置,缝合固定4周,移除后9个月CBCT显示明显骨沉积、根尖周透射影显著缩小并与鼻腭管分离。提示减压术本身可作为大型根尖周病变的治疗选择。
要点
- 大型根尖周病变单独正畸根管治疗常不足以促进愈合。
- 3D打印定制减压装置固定4周,9个月后CBCT示骨沉积与病变缩小。
- 减压装置可减少囊内压力,配合冲洗降低炎症化合物。
核心结论
- 手术减压术本身可作为大型根尖周病变的一种治疗选择,促进骨沉积和病变缩小。
研究设计与样本
- 病例报告:1例21岁男性,右上前牙根管治疗后大型根尖周病变累及鼻腭管及颊舌侧皮质骨穿孔。
主要发现
- CBCT确认根管充填致密,遂仅行手术减压保守治疗。
- 定制减压装置缝合固定4周,移除后9个月CBCT示骨沉积、根尖周透射影显著缩小并与鼻腭管分离。
临床怎么用
- 对根管充填完善的大型根尖周病变,可考虑单独使用定制减压装置替代传统摘除术。
- 利用CBCT与数字软件设计个性化减压装置,减少传统材料(吸引管、针头、橡皮障)引起的刺激和不稳定。
局限性
- 单例病例报告,证据等级有限,结论需更大样本验证。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIM: A case report to describe the use of a novel 3D printed surgical decompression device to induce healing of large periapical lesions. SUMMARY: The development of periapical pathology is influenced by a variety of factors including local microbiology and pathophysiology. In large lesions, lone orthograde endodontic treatment is often insufficient in promoting healing of the periapical tissues and therefore is followed by apical surgery to reduce inflammation. While traditional surgical treatments often involve enucleation for cystic lesions, decompression techniques have shown to provide a less invasive alternative when combined with non-surgical and/or surgical endodontic treatment. The case presented here is a 21-year-old male with a large periapical lesion involving a root canal-treated right maxillary central incisor and nasopalatine canal; extending from the maxillary right lateral incisor to the maxillary left central incisor and having perforated buccal and lingual cortical plates. Clinically, the patient reported an associated fluctuant, non-tender buccal swelling. CBCT confirmed a well-condensed root canal filling; hence, it was decided to first treat the lesion conservatively using only the surgical decompression technique. Following a discussion about treatment options, the patient consented to surgical decompression. CBCT imaging alongside digital software was used to fabricate a customised decompression device that was sutured in situ for 4 weeks. Nine months following the removal of the device, CBCT showed evidence of osseous deposition, with a significant reduction of the periapical radiolucency and separation from the nasopalatine canal, thus portraying the use of decompression in its own right as a treatment option. Surgical decompression is not a novel technique, and the literature describes the use of various dental equipment such as suction tubing, needle hub, or dental dam material to facilitate decompression of a lesion. These devices have, however, shown to cause irritation, discomfort, and instability and are therefore not always effective in inducing healing. This case report describes the use of a novel digital workflow to fabricate a customised decompression device in the management of a large periapical lesion. The reduction of intra-cystic pressure alongside active irrigation reduced inflammatory compounds, contributing to a reduction in the lesion size and promoting osseous healing.
引用
- Patel Y, Razaghi N, Patel M, et al. The Use of a Novel 3D Printed Surgical Decompression Device to Induce Healing of Large Periapical Lesions: A Case Report. Int Endod J. 2025. PMID: 41104857. doi:10.1111/iej.70053
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。