径向刃带与交替切削刃可降低弯曲根管中的螺钉效应与扭矩
结果显示不同锉在根向力、螺钉效应和扭矩上存在显著差异(P < .05),牙齿z轴扭矩与马达扭矩显著相关(P < .001)。结论认为径向刃带或交替切削刃会影响镍钛锉的螺钉效应和扭转载荷。
要点
- 径向刃带或交替切削刃可降低弯曲根管中镍钛锉的螺钉效应和扭矩。
- 不同镍钛锉系统在根向力、螺钉效应和扭矩上存在显著差异。
- 牙齿z轴扭矩与马达测得扭矩显著相关,可作为评估参考。
核心结论
- 径向刃带或交替切削刃会影响镍钛锉的螺钉效应和扭转载荷。
研究设计与样本
- 各组在工作长度、弦长和根管弯曲度上标准化均衡,采用定制测试台和6轴测量装置测量力与扭矩。
主要发现
- 不同镍钛锉在根向力、螺钉效应和扭矩上存在显著差异(P < .05)。
- 牙齿沿z轴产生的扭矩与马达测得的锉扭矩显著相关(P < .001)。
临床怎么用
- 临床选择镍钛锉时,可考虑径向刃带或交替切削刃设计以降低弯曲根管中的螺钉效应和扭转载荷。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: This study aimed to evaluate screw-in force and torsional load generated by 6 fully rotating nickel-titanium (NiTi) file systems with different geometry, cross-section, and rotational speed. METHODS: Ninety mesial roots of human lower molars were divided into 6 groups according to the file system used for canal preparation: F360, F6, TruNatomy, RACE EVO, JIZAI I, and JIZAI II. Groups were standardized balanced to working length, chord length, and canal curvature. A custom-built test rig with an attached endodontic motor (Schlumbohm EndoPilot 2) and a 6-axis measuring device were used to measure the apically directed, screw-in and torque forces generated along the axis of the tooth as the NiTi file was moved with an amplitude of 3 mm at each peck, increasing penetration depth by 2 mm at each peck. The rotary speed was set individually for each file according to the manufacturer's instructions. Two sets of 3 pecking motions were performed with intermitting cleanings of the file and needle irrigation of the root canal. Additionally, torque forces were recorded by the endodontic motor. Maximum force values for each set of pecks were analyzed using the Kruskal-Wallis test. The correlation between z-axis tooth torque and motor-measured torque was assessed using Spearman's correlation. RESULTS: Significant differences existed between the files regarding apically directed, screw-in and torque forces (P < .05). Torque values generated on the tooth along the z-axis and torque on the file correlated significantly (P < .001). CONCLUSIONS: Radial lands or alternating cutting edges affect screw-in effect and torsional load of NiTi files.
引用
- Heimberg G, Bürklein S, Schäfer E, et al. Radial Lands and Alternating Cutting Edges Contribute to Reduced Screw-in and Torque in Curved Root Canals - An In Vitro Study. J Endod. 2025. PMID: 41061817. doi:10.1016/j.joen.2025.09.019
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。