文献速递口腔修复与种植口腔颌面外科

SealPrint技术:解剖复制型封闭支持种植体基台12个月随访验证

SealPrint: The anatomically replicated seal-and-support socket abutment technique A Proof-of-Concept with 12 months of follow-up.
PubMed 文献 · J Dent · 2025-07-02

本研究探索利用AI驱动的牙齿分割与3D打印技术设计制造封闭支持基台(SealPrint)的新方法,在即刻种植后覆盖临时基台以封闭拔牙窝。12个月随访显示SealPrint被动就位、密封拔牙窝、保护种植体与移植材料,并维持软硬组织与穿龈轮廓。

要点

  • AI分割CBCT牙齿结合口内扫描可设计解剖复制型封闭基台。
  • SealPrint被动就位于临时基台上,密封整个拔牙窝表面。
  • 该技术保护种植体与移植材料,维持穿龈轮廓和龈乳头。

核心结论

  • SealPrint技术为即刻种植后软硬组织及穿龈轮廓的保护与保存提供可靠快速的解决方案。

研究设计与样本

  • 本研究为技术验证性概念研究,采用AI驱动牙齿分割与3D打印技术设计制造封闭支持基台,并进行了12个月随访。

主要发现

  • SealPrint与计划一致,被动就位于临时基台上。
  • SealPrint密封整个拔牙窝表面,保护种植体,稳定移植材料与血凝块。
  • SealPrint保留了拔除牙的穿龈轮廓。

关键数值与推荐

  • AI分割的牙齿在临时基台颈部水平切片,并在龈缘上方2 mm修剪以捕捉穿龈轮廓。
  • 锥形切割比临时基台宽2 mm,锥度5°,以实现被动就位。

临床怎么用

  • 在即刻种植病例中,可应用SealPrint技术封闭拔牙窝并支持龈乳头。
  • 使用流动树脂填充临时基台与SealPrint之间的间隙以完成密封结构。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: This study aimed at investigating a novel technique for designing and manufacturing a sealing socket abutment (SSA) using artificial intelligence (AI)-driven tooth segmentation and 3D printing technologies. METHODS: A validated AI-powered module was used to segment the tooth to be replaced on the presurgical Cone Beam Computed Tomography (CBCT) scan. Following virtual surgical planning, the CBCT and intraoral scan (IOS) were imported into Mimics software. The AI-segmented tooth was aligned with the IOS, sliced horizontally at the temporary abutment's neck, and further trimmed 2 mm above the gingival margin to capture the emergence profile. A conical cut, 2 mm wider than the temporary abutment with a 5° taper, was applied for a passive fit. This process produced a custom sealing socket abutment, which was then 3D-printed. After atraumatic tooth extraction and immediate implant placement, the temporary abutment was positioned, followed by the SealPrint atop. A flowable composite was used to fill the gap between the temporary abutment and the SealPrint; the whole structure sealing the extraction socket, providing by design support for the interdental papilla and protecting the implant and (bio)materials used. RESULTS: True to planning, the SealPrint passively fits on the temporary abutment. It provides an optimal seal over the entire surface of the extraction socket, preserving the emergence profile of the extracted tooth, protecting the dental implant and stabilizing the graft material and blood clot. CONCLUSIONS: The SealPrint technique provides a reliable and fast solution for protection and preservation of the soft-, hard-tissues and emergence profile following immediate implant placement.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Lahoud P, Castro A, Walter E, et al. SealPrint: The anatomically replicated seal-and-support socket abutment technique A Proof-of-Concept with 12 months of follow-up. J Dent. 2025. PMID: 40615065. doi:10.1016/j.jdent.2025.105948

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。