文献速递牙体牙髓病

不同锥度根管预备后下颌磨牙近中根牙本质保存与应力分布的Micro-CT及有限元分析

Micro-CT and Finite Element Analysis of Dentin Preservation and Stress Distribution in Mesial Roots of Mandibular Molars after Shaping with Different Tapers.
PubMed 文献 · J Endod · 2025-07-01

Micro-CT显示B4U组颈侧牙本质去除量显著低于PG组,根管中心定位能力更优,冠状及危险区残余牙本质厚度更高;有限元分析显示各组应力分布无显著差异。结论提示减小根管锥度可能改善中心定位与残余牙本质保存,但锥度不影响近中根应力分布模式。

要点

  • B4U组颈侧牙本质去除量显著低于PG组,中心定位能力在冠、中三分之一更优。
  • B4U组在冠部分析点及危险区的近远中侧残余牙本质厚度显著更高。
  • 有限元分析显示各器械组间近中根应力分布无统计学显著差异。

核心结论

  • 减小根管锥度可能改善器械中心定位能力并保存残余牙本质,尤其在冠和中三分之一。
  • 根管锥度似乎不影响下颌磨牙近中根的应力分布模式。

研究设计与样本

  • 预备前后行Micro-CT扫描,比较根管体积与颈侧牙本质体积,分析中心偏移及牙本质去除百分比与分布。
  • 测量近中根管远中与近中面残余牙本质厚度,并建立下颌磨牙近中根线性弹性有限元模型,于根管冠三分之一施加200N垂直载荷。
  • 采用单因素方差分析及Bonferroni校正与Tukey-Kramer事后检验(P < .05)。

主要发现

  • B4U组平均颈侧牙本质体积去除量显著低于PG组(P < .05)。
  • B4U组在冠和中三分之一的根管中心定位能力显著更优,PG组中心偏移变化更大(P < .05)。
  • B4U组在冠部分析点及危险区的近中与远中根面残余牙本质厚度显著更高(P < .05)。
  • PG组在根管冠三分之一去除更多牙本质(P < .05)。
  • 有限元分析显示各组间无统计学显著差异(P > .05)。

临床怎么用

  • 临床预备下颌磨牙近中根管时,可优先考虑锥度较小的器械以保存冠部及危险区牙本质。
  • 关注根管冠三分之一与危险区的牙本质去除,以降低牙根薄弱风险。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The aim of this study was to evaluate the dentin preservation and fracture resistance of mandibular molar mesial roots after shaping with different tapers using micro-computed tomography (micro-CT) and finite element analysis (FEA). METHODS: Forty-eight mandibular first molars with independent mesial canals were selected. The mesio-lingual and mesio-buccal canals were randomly assigned (n = 12) to ProTaper Gold (PG), ProTaper Next (PTN), ProTaper Ultimate (PTU), and B4U instrumentation systems. Pre- and post-shaping micro-CT scans were performed to compare root canal volume and cervical dentin volume. The centroid shift and the percentage and distribution of the dentin removal in correspondence of the mesial canals were analyzed in coronal, middle, and apical points of analysis and below the furcation at the "danger zone." The residual dentin thickness in the distal and mesial aspects of the mesial canals was measured. A linear elastic model of a mesial root of a mandibular molar was created through the finite element method (FEM) and a 200N perpendicular load was applied on the root canal coronal third. One-way factorial analysis of variance with Bonferroni correction and post hoc Tukey-Kramer tests were used (P < .05). RESULTS: The mean cervical dentin volume removal was statistically lower for the B4U compared with the PG system (P < .05). The canal centering ability was statistically more accentuated for the B4U group in the coronal and middle third and higher centroid shift variations occurred for PG system (P < .05). The residual dentin thickness appeared statistically higher after shaping with B4U through the mesial and distal root aspect at the coronal point of analysis and at the danger zone (P < .05). PG removed more dentin in the coronal root canal third (P < .05). The FEM analysis showed no statistically significant differences between groups (P > .05). CONCLUSIONS: The reduction of the root canal taper may improve the instruments' centering ability and the preservation of the residual dentin tissue, especially in the coronal and middle third. The root canal taper seems not to influence the stress distribution pattern through the mesial root of the lower molars.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Alovisi M, Baldi A, Moccia E, et al. Micro-CT and Finite Element Analysis of Dentin Preservation and Stress Distribution in Mesial Roots of Mandibular Molars after Shaping with Different Tapers. J Endod. 2025. PMID: 40609828. doi:10.1016/j.joen.2025.06.017

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。