附加垂直运动对镍钛旋转器械在最佳扭矩反转模式下的扭矩、力及根管成形性能的影响
本研究在35个J形树脂根管中比较连续旋转与不同参数最佳扭矩反转(OTR)运动下ProTaper Next的扭矩、力和中心定位能力。结果显示OTR配合1.0秒下压的强制进出运动可降低力/扭矩及中心定位偏差,且不延长操作时间。
要点
- OTR配合1.0秒下压强制进出运动可减小顺时针扭矩和向下力。
- OTR-0.25s组操作时间最长,其他组未见时间延长。
- CR和OTR-0.25s组在根尖0 mm和0.5 mm处中心定位偏差显著更大。
核心结论
- 在ProTaper Next旋转器械中使用OTR运动时,加入下压持续1.0秒的强制进出运动可降低力/扭矩产生和中心定位偏差,且不延长操作时间。
研究设计与样本
- 在35个J形树脂根管中,使用ProTaper Next X1至X3进行带扭矩/力传感的自动化根管预备,并施加周期性上下运动。
- 分组为连续旋转(CR组)、无强制进出运动的OTR运动(OTR-N组)以及下压持续0.25秒、1.0秒和2.0秒的强制进出OTR运动(OTR-0.25s组、OTR-1s组、OTR-2s组)。
- 评估最大扭矩/力值、操作时间和根管中心定位比,采用双因素方差分析后行简单主效应检验或Tukey检验(α=0.05)。
主要发现
- OTR-0.25s组和OTR-1s组通常表现出显著更小的顺时针扭矩(P<.05)。
- CR组、OTR-0.25s组和OTR-1s组通常表现出显著更小的向下力(P<.05)。
- CR组和OTR-0.25s组在根尖0 mm和0.5 mm处的中心定位比显著更高(偏差更大)(P<.05)。
- OTR-0.25s组操作时间最长(P<.05)。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: Optimal manipulation techniques for nickel-titanium rotary instrumentation using optimum torque reverse (OTR) motion, a torque-sensitive reciprocating motion, remain underexplored. This study evaluated the effects of applying "forced in-and-out motion" (i.e., downward followed by immediate upward movement upon OTR activation) on the performance of ProTaper NEXT instrumentation. METHODS: An automated instrumentation with torque/force sensing was conducted in 35 J-shaped resin canals with ProTaper Next X1 to X3, employing periodic up-and-down movements. The applied motions were; continuous rotation (group CR); OTR motion without forced in-and-out motion (group OTR-N); and OTR motion with forced in-and-out motion, featuring downward movements lasting 0.25 s, 1.0 s, and 2.0 s (groups OTR-0.25s, OTR-1s, and OTR-2s). Maximum torque/force values, instrumentation time, and canal-centering ratios were evaluated. Statistical analysis was conducted adopting two-way analysis of variance followed by a simple main effect test or Tukey test (α = 0.05). RESULTS: Groups OTR-0.25s and OTR-1s typically demonstrated significantly smaller clockwise torque, and groups CR, OTR-0.25s, and OTR-1s generally exhibited significantly smaller downward force, relative to the other groups (P < .05). Groups CR and OTR-0.25s demonstrated significantly higher canal-centering ratios (more deviations) at apical 0 mm and 0.5 mm than the other groups (P < .05). Group OTR-0.25s had the longest instrumentation time (P < .05). CONCLUSIONS: When adopting OTR motion in ProTaper Next rotary instrumentation, incorporating forced in-and-out motion with 1.0 s of downward movement reduced force/torque generation and canal-centering ratios without extending instrumentation time.
引用
- Kimura S, Ebihara A, Maki K, et al. Effects of Additional Vertical Movements on the Torque, Force, and Root Canal Shaping Performance of Nickel-Titanium Rotary Instruments in Optimal Torque Reverse Motion. J Endod. 2025. PMID: 40316205. doi:10.1016/j.joen.2025.04.014
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。