重复使用对3种旋转锉循环疲劳与扭转疲劳的影响:对临床安全的启示
本研究比较S2、Logic和Flat File镍钛锉在全新及经本科生重复使用后的循环疲劳与扭转疲劳性能。在模拟60°弯曲根管的装置中测试#25和#35直径器械,结果显示重复使用对#25和#35直径器械的力学性能产生负面影响,尤其是Flat File和Logic器械。
要点
- 全新#25直径器械中Logic断裂前循环数最高,Flat File最低(P<.05)。
- 使用后#25直径器械中Logic和S2断裂前循环数优于Flat File(P<.05)。
- 重复使用后所有#25直径器械角偏转显著增加(P<.05)。
核心结论
- 重复使用对#25和#35直径牙髓器械的力学性能产生负面影响,尤其是Flat File和Logic器械。
- Logic #35直径器械的最大扭矩和角偏转高于新器械,仅Logic在重复使用后角偏转显著降低(P<.05)。
研究设计与样本
- 体外研究:使用90颗(n=90)人工下颌磨牙,分别用S2、Logic和Flat File系统预备。
- 每种系统10支新器械进行力学测试,另10支在预备3颗弯曲近中根(60°)的原型磨牙后测试。
- 循环疲劳测试在模拟弯曲根管(弯曲角60°、半径5 mm)的定制装置中进行,扭转强度测试遵循ISO 3630-1(1992)标准。
- 数据分析采用方差分析和Tukey检验(P = .05)。
主要发现
- 全新#25直径器械中,Logic断裂前循环数最高,Flat File最低(P<.05)。
- 使用后#25直径器械中,Logic和S2断裂前循环数优于Flat File(P<.05)。
- 使用后Flat File #25直径器械重复使用后断裂前循环数显著下降,且断裂前最大扭矩最低(P<.05)。
- 所有#25直径器械重复使用后角偏转显著增加(P<.05)。
- #35直径器械中,S2和Logic优于Flat File(P<.05)。
关键数值与推荐
- 全新#25直径器械断裂前循环数:Logic最高,Flat File最低(P<.05)。
- 使用后#25直径器械断裂前循环数:Logic和S2优于Flat File(P<.05)。
- 使用后Flat File #25直径器械断裂前循环数显著下降、断裂前最大扭矩最低(P<.05)。
- 所有#25直径器械重复使用后角偏转显著增加(P<.05)。
- #35直径器械:S2和Logic优于Flat File(P<.05)。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: This study aimed to compare the cyclic and torsional fatigue of S2, Logic, and Flat File NiTi files, new and after repeated use by an undergraduate student. METHODS: Ninety (n = 90) artificial mandibular molars were prepared using S2, Logic, and Flat File systems. For each system, 10 new instruments were tested mechanically, and the other 10 were tested after preparing three prototyped molars with curved mesial roots (60°). Cyclic fatigue tests were conducted in a custom device simulating a curved canal (60° curvature angle, 5 mm radius), while torsional strength tests followed ISO 3630-1 (1992) standards. Data were analyzed by analysis of variance and Tukey's tests (P = .05). RESULTS: Among the new #25-diameter instruments, Logic exhibited the highest number of cycles to fracture, while Flat File had the lowest (P < .05). For the used #25-diameter instruments, Logic and S2 demonstrated superior performance than Flat File regarding cycles to fracture (P < .05). The used Flat File #25-diameter instruments demonstrated a significant decrease in cycles to fracture after repeated use, and the lowest maximum torque until fracture (P < .05). All #25-diameter instruments showed a significant increase in angular deflection after repeated use (P < .05). For the #35-diameter instruments, S2 and Logic outperformed Flat File (P < .05). CONCLUSIONS: The Logic #35-diameter instruments displayed higher maximum torque and angular deflection than the new instruments, with only Logic showing significant reductions in angular deflection after use (P < .05). The repeated use negatively affected the mechanical properties of the endodontic instruments with #25 and #35 diameters, particularly the Flat File and Logic instruments.
引用
- Sales de Oliveira Neto R, da Rocha Tavares Duarte R, Hungaro Duarte MA, et al. Impact of Repeated Use on Cyclic and Torsional Fatigue of 3 Rotary Files: Implications for Clinical Safety. J Endod. 2025. PMID: 40268242. doi:10.1016/j.joen.2025.04.008
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。