不同基台设计及无基台种植体连接下整体氧化锆螺钉固位固定牙修复体的承载能力
本研究比较了无基台整体氧化锆、无基台饰面钛、钛基底基台氧化锆、多单元基台氧化锆及多单元基台饰面钛五种三单位螺钉固位固定牙修复体在热机械老化后的扭矩变化与初始及最终失败载荷。结果显示所有螺钉扭矩均下降,钛组初始失败载荷显著较低而最终失败载荷显著较高。无基台整体氧化锆修复体失败载荷与其他氧化锆组相似。
要点
- 热机械老化后所有螺钉扭矩均下降,多单元基台饰面钛组扭矩下降显著大于无基台饰面钛组(p=0.0021)。
- 钛组初始失败载荷显著低于氧化锆组(171.4-230 N vs 1272-1358 N,p=0.0001),因饰面瓷断裂。
- 钛组最终失败载荷显著高于氧化锆组(2922-3029 N vs 1272-1358 N,p<0.0001)。
核心结论
- 三单位无基台整体氧化锆固定牙修复体的失败载荷与其他氧化锆组相似,而钛组表现出更高的最终失败载荷。
- 不同基台设计似乎不影响失败载荷。
研究设计与样本
- 体外研究,将50个三单位螺钉固位固定牙修复体(共100颗种植体)按种植体-基台连接和上部结构材料分为5组,每组10个。
主要发现
- 热机械老化后所有螺钉扭矩均下降,多单元基台饰面钛组扭矩下降显著大于无基台饰面钛组(p=0.0021)。
- 钛组初始失败载荷(171.4-230 N)显著低于氧化锆组(1272-1358 N),因饰面瓷断裂(p=0.0001)。
- 钛组最终失败载荷(2922-3029 N)显著高于氧化锆组(1272-1358 N)(p<0.0001)。
临床怎么用
- 作者认为,无基台种植体连接上的整体氧化锆固定牙修复体可放心使用,因其机械稳定性与钛基底基台或多单元基台上的整体氧化锆固定牙修复体相似。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: A new abutment-free implant connection allows for direct screwing of FDPs on implants to avoid complications caused by cement rests or screw loosening, which may affect to screw torque and load distribution. The objective of this study was to test the initial (Fi) and final failure (Ff) loads and torque changes of abutment-free monolithic zirconia CAD-CAM fixed dental prostheses (FDPs) compared to titanium FDPs on different abutment designs. METHODS: Three-unit screw-retained FDPs (n = 50) on two implants (n = 100) were divided into groups (n = 10) based on the implant-abutment connection and material of the supra-structure: (1) abutment-free monolithic CAD-CAM zirconia FDP (Abut-free-Zr), (2) abutment-free veneered titanium FDPs (Abut-free-Ti), (3) monolithic zirconia FDPs with titanium base abutments (Zr-Ti-Base), (4) monolithic zirconia FDPs on multi-unit abutments (Zr-MU), (5) veneered titanium FDP on multi-unit abutments (Ti-MU). All specimens were subjected to thermo-mechanical aging (1'200'000 Cycles, 49 N, 1.67 Hz, 5º to 50º C, dwelling time 120 s). Torque of the screws was measured, and static loading was performed. Data were tested using ANOVA and Tukey's tests (p < 0.05). RESULTS: After thermo-mechanical aging, all screws showed reduced torque, Ti-MU significantly more reduction compared to Abut-Free-Ti (p = 0.0021). Titanium groups showed significantly lower Fi (N) values (171.4-230 vs 1272-1358,) due to veneering porcelain fractures (p = 0.0001) and significantly higher Ff (N) (2922 -3029 N vs. 1272-1358) values than zirconia groups (p < 0.0001). CONCLUSIONS: Three-unit abutment-free monolithic zirconia FPDs showed similar failure loads compared to other zirconia groups, while the titanium groups exhibited superior final failure loads. Different abutment designs did not seem to affect the failure loads. CLINICAL SIGNIFICANCE: The specific design of the novel implant interface allows for the fabrication of implant supported FDPs with personalized design directly on implant level without abutments. The monolithic zirconia FDPs on abutment-free implant connection can be used with good confidence since they exhibit similar mechanical stability as monolithic zirconia FDPs on titanium-base or multi-unit abutments.
引用
- Schäfer T, Mätzener KJ, Jung RE, et al. Load-bearing capacity of screw-retained fixed dental prostheses made of monolithic zirconia on different abutment designs and abutment-free implant connection. J Dent. 2025. PMID: 39778736. doi:10.1016/j.jdent.2025.105561
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。