激光织构氧化锆表面涂覆富血小板纤维蛋白后的摩擦行为
本体外研究评估可注射富血小板纤维蛋白(i-PRF)在激光织构氧化锆表面的黏附及其对骨组织的摩擦行为。比较喷砂酸蚀(ZLA)、随机激光织构(RD)和设计图案激光织构(L16N8)三种表面,在1 N载荷、1 Hz、2 mm行程下测试摩擦系数。结果显示除RD组外,测试组摩擦系数低于对照组;RD与L16N8涂覆后无显著差异。三维纤维网络提供润滑效应,激光织构形貌可增加纤维蛋白黏附,可能加速氧化锆种植体骨整合。
要点
- 除RD组外,i-PRF涂覆后测试组摩擦系数低于对照组。
- RD与L16N8表面涂覆i-PRF后摩擦系数无显著差异。
- 三维纤维网络嵌入白细胞、血小板和红细胞,提供润滑效应。
核心结论
- 除RD组外,i-PRF涂覆后测试组摩擦系数低于对照组。
- RD与L16N8表面涂覆i-PRF后摩擦系数无显著差异。
- 三维纤维网络嵌入白细胞、血小板和红细胞,降低氧化锆表面摩擦系数,提供润滑效应。
- 激光处理氧化锆表面的形貌特征增加富血小板纤维蛋白黏附,可能加速氧化锆种植体骨整合过程。
研究设计与样本
- 体外研究,比较三种氧化锆表面(ZLA、RD、L16N8)的i-PRF涂层效果。
- ZLA为250微米球形氧化铝颗粒喷砂后20%氢氟酸酸蚀。
- RD为随机图案激光织构,L16N8为基于16条线和8个通道的设计图案激光织构。
- 在往复滑动销-盘摩擦磨损试验机上测试摩擦系数,条件为1 N法向载荷、1 Hz、2 mm行程。
- 滑动磨损测试在室温0.9%氯化钠溶液中对牛股骨骨组织进行,后用扫描电子显微镜评估表面。
主要发现
- ZLA组摩擦系数均值:测试组0.35,对照组0.52。
- L16N8组摩擦系数均值:测试组0.45,对照组0.60。
- RD组摩擦系数均值:测试组0.47,对照组0.43。
- RD与L16N8表面涂覆i-PRF后摩擦系数均值无显著差异。
- 三维纤维网络嵌入白细胞、血小板和红细胞,降低氧化锆表面摩擦系数,提供润滑效应。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
In the present in vitro study, we evaluated the adhesion of an injectable platelet-rich fibrin (i-PRF) to laser-textured zirconia surfaces and their resultant friction behavior against bone tissue. Three types of zirconia surfaces were compared regarding the i-PRF coating effects: 1) grit blasted with 250-μm spherical alumina particles and acid etched with 20% hydrofluoric acid (ZLA), 2) laser textured with a random (RD) surface pattern, or 3) laser textured with a designed pattern based on 16 lines and 8 passages (L16N8). The coefficient of friction (COF) of the specimens was assessed on a reciprocating sliding pin-on-plate tribometer at 1-N normal load, 1 Hz, and a 2-mm stroke length. Sliding wear tests were carried out against bovine femoral bone tissue in 0.9% sodium chloride solution at room temperature. Surfaces were then assessed by scanning electron microscopy. COF mean values for test groups (0.35, ZLA; 0.45, L16N8) were lower when compared with the control groups (0.52, ZLA; 0.60, L16N8), with the exception of the RD group (0.47, test; 0.43, control). Results did not show significant differences in COF mean values between RD and L16N8 surfaces after coating with i-PRF. The 3-dimensional fibrin network embedded with leukocytes, platelets, and red blood cells was responsible for decreasing COF mean values over the zirconia surfaces, thus providing a lubricant effect. Also, the morphologic aspects of the laser-treated zirconia surfaces increased the adhesion of the platelet-rich fibrin, which could speed up the osseointegration process of zirconia implants.
引用
- Oliveira MN, Sahoo N, Carvalho O, et al. Friction of Laser-Textured Zirconia Coated with a Platelet-Rich Fibrin. J Dent Res. 2025. PMID: 39876090. doi:10.1177/00220345241305318
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。