文献速递口腔修复与种植口腔颌面外科

定制钛网与钛增强e-PTFE网行垂直骨增量非劣效随机试验

Complication, vertical bone gain, volumetric changes after vertical ridge augmentation using customized reinforced PTFE mesh or Ti-mesh. A non-inferiority randomized clinical trial.
PubMed 文献 · Clin Oral Implants Res · 2024-08-23

本非劣效随机临床试验纳入50例垂直骨缺损患者,比较定制钛增强d-PTFE网与CAD/CAM钛网联合自体骨和脱蛋白牛骨基质行垂直骨增量的手术及愈合并发症、垂直骨增量和体积变化。结果显示两者并发症非劣效,PTFE组垂直骨增量和再生率数值较高但无显著差异。

要点

  • 定制CAD/CAM钛网在手术和愈合并发症方面不劣于钛增强PTFE网。
  • PTFE组垂直骨增量5.79±1.71 mm,钛网组5.18±1.61 mm,差异无统计学意义(p=.233)。
  • PTFE组再生率99.5%显著高于钛网组87.0%(p=.013)。

核心结论

  • 定制CAD/CAM钛网在手术和愈合并发症方面不劣于钛增强PTFE网。
  • PTFE网垂直骨增量和再生率数值高于钛网,但垂直骨增量差异无统计学意义。
  • 两组骨密度、种植体稳定性和骨结合率相似。

研究设计与样本

  • 非劣效随机临床试验,50例垂直骨缺损患者随机分为钛增强d-PTFE网组(对照)和CAD/CAM钛网组(试验)。
  • 48例患者接受骨增量手术,植骨材料为自体骨与脱蛋白牛骨基质混合。
  • 记录并分析手术和愈合并发症率、垂直骨增量、再生骨体积及再生率,显著性水平α=0.05。

主要发现

  • 手术并发症率PTFE组4%、钛网组12%;愈合并发症率PTFE组12.5%、钛网组8.3%。
  • 垂直骨增量PTFE组5.79±1.71 mm(范围3.2-8.8 mm),钛网组5.18±1.61 mm(范围3.1-8.0 mm),p=.233。
  • 再生骨体积PTFE组1.46±0.48 cc,钛网组1.26±0.55 cc。
  • 再生率PTFE组99.5%、钛网组87.0%,差异有统计学意义(p=.013)。
  • 骨结合率PTFE组98.2%、钛网组98.3%;假骨膜、骨密度和种植体稳定性两组相似。

临床怎么用

  • 对于垂直骨缺损,定制CAD/CAM钛网可作为钛增强PTFE网的替代选择,并发症风险不更高。
  • 若追求更高的垂直骨增量和再生率,钛增强PTFE网可能略有优势,但需权衡并发症。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: The aim of this non-inferiority randomized clinical trial was to compare the surgical and healing complications, vertical bone gain, and volumetric bone changes after vertical ridge augmentation using two different approaches: customized Ti-reinforced d-PTFE mesh versus customized CAD/CAM Ti-mesh. MATERIALS AND METHODS: Fifty patients with vertical bone defects were randomly treated with Ti-reinforced d-PTFE mesh (control group) or CAD/CAM Ti-mesh (test group) and a mix of autogenous bone and deproteinized bovine bone matrix. Surgical and healing complication rates (SCR-HCR), vertical bone gain (VBG), regenerated bone volume (RBV), and regeneration rates (RR and ERR) were recorded and analysed [significance level (α) of 0.05]. RESULTS: Of the 50 patients, 48 underwent bone augmentation surgery. SCR were 4% and 12% in PTFE and Ti-mesh, whereas HCR were 12.5% and 8.3%. VBG were 5.79 ± 1.71 mm (range: 3.2-8.8 mm) in the PTFE group and 5.18 ± 1.61 mm (range: 3.1-8.0 mm) in the Ti-mesh group (p = .233), whereas RBV were 1.46 ± 0.48 cc and 1.26 ± 0.55. RR was 99.5% and 87.0%, demonstrating a statistically significant difference (p = .013). Finally, the values related to pseudo-periosteum, bone density, and implant stability were similar in the two study groups. Osseointegration rates were 98.2% and 98.3%. CONCLUSIONS: This study confirmed the non-inferiority of customized CAD/CAM titanium meshes with respect to reinforced PTFE meshes in terms of surgical and healing complications. Although PTFE meshes showed higher vertical bone gain and regeneration rates than Ti-meshes, no significant differences were found.

来源:Clin Oral Implants Res,查看原文。版权归原作者所有。

引用

  1. Cucchi A, Bettini S, Tedeschi L, et al. Complication, vertical bone gain, volumetric changes after vertical ridge augmentation using customized reinforced PTFE mesh or Ti-mesh. A non-inferiority randomized clinical trial. Clin Oral Implants Res. 2024. PMID: 39180274. doi:10.1111/clr.14350

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。