文献速递口腔修复与种植

3D打印患者特异性可吸收支架用于牙种植位点牙槽骨再生的病例报告

Alveolar bone regeneration using a 3D-printed patient-specific resorbable scaffold for dental implant placement: A case report.
PubMed 文献 · Clin Oral Implants Res · 2024-08-07

本病例报告展示了一例46岁男性缺失11牙患者,采用3D打印患者特异性聚己内酯(PCL)可吸收支架行分期牙槽骨增量。结果显示体积骨增益为364.69 ± 2.53 mm3,组织学证实新骨形成及移植物整合,种植体获得35 Ncm-1初期稳定性,术后疼痛轻微。

要点

  • 3D打印PCL支架实现364.69 ± 2.53 mm3体积骨增益,足以重建牙槽骨轮廓。
  • 组织学显示缺损各区新骨形成及移植物颗粒间连续新骨。
  • 种植体初期稳定性达35 Ncm-1,术后疼痛轻微。

核心结论

  • 3D打印患者特异性PCL支架引导的骨再生可实现牙槽骨增量并支持后续种植体植入。

研究设计与样本

  • 病例报告:1例46岁男性缺失11牙,行分期牙槽骨增量使用患者特异性PCL支架,评估体积骨增益、种植体稳定性及组织学。

主要发现

  • 体积骨增益为364.69 ± 2.53 mm3,足以重建原始牙槽骨轮廓并允许种植体植入。
  • 组织学分析显示所有缺损区(冠方、中间、根方)均有新骨存在及移植物成功整合,移植物颗粒周围及之间连续新骨形成。
  • 种植体获得35 Ncm-1初期稳定性。
  • 骨增量术后计划种植位置与术前修复驱动种植计划相比整体偏差2.4°。
  • 患者报告术后前48小时平均每日疼痛低,从第3天起无疼痛。

临床怎么用

  • 对于需分期牙槽骨增量的牙种植病例,可考虑使用3D打印患者特异性可吸收支架引导骨再生。

局限性

  • 仅为单例病例报告,结论需更大样本研究验证。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: This case report demonstrates the effective clinical application of a 3D-printed, patient-specific polycaprolactone (PCL) resorbable scaffold for staged alveolar bone augmentation. OBJECTIVE: To evaluate the effectiveness of a 3D-printed PCL scaffold in facilitating alveolar bone regeneration and subsequent dental implant placement. MATERIALS AND METHODS: A 46-year-old man with a missing tooth (11) underwent staged alveolar bone augmentation using a patient-specific PCL scaffold. Volumetric bone gain and implant stability were assessed. Histological analysis was conducted to evaluate new bone formation and graft integration. RESULTS: The novel approach resulted in a volumetric bone gain of 364.69 ± 2.53 mm3, sufficient to reconstruct the original alveolar bone contour and permit dental implant placement. Histological analysis showed new bone presence and successful graft integration across all defect zones (coronal, medial, and apical), with continuous new bone formation around and between graft particles. The dental implant achieved primary stability at 35 Ncm-1, indicating the scaffold's effectiveness in promoting bone regeneration and supporting implant therapy. The post-grafting planned implant position deviated overall by 2.4° compared with the initial restoratively driven implant plan pre-bone augmentation surgery. The patient reported low average daily pain during the first 48 h and no pain from Day 3. CONCLUSIONS: This proof-of-concept underscores the potential of 3D-printed scaffolds in personalized dental reconstruction and alveolar bone regeneration. It marks a significant step forward in integrating additive manufacturing technologies into clinical practice through a scaffold-guided bone regeneration (SGBR) approach. The trial was registered with the Australian New Zealand Clinical Trials Registry (ACTRN12622000118707p).

来源:Clin Oral Implants Res,查看原文。版权归原作者所有。

引用

  1. Ivanovski S, Staples R, Arora H, et al. Alveolar bone regeneration using a 3D-printed patient-specific resorbable scaffold for dental implant placement: A case report. Clin Oral Implants Res. 2024. PMID: 39109582. doi:10.1111/clr.14340

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。