文献速递牙体牙髓病

新型多色热处理镍钛旋转系统的多方法分析:设计、冶金、机械性能与成形能力

Multimethod Analysis of a Novel Multi-coloured Heat-treated Nickel-Titanium Rotary System: Design, Metallurgy, Mechanical Properties, and Shaping Ability.
PubMed 文献 · J Endod · 2024-07-30

本研究采用多方法比较RCS Rainbow与四种热处理旋转镍钛器械的设计、冶金、机械性能和成形能力。结果显示RCS Rainbow在柔顺性和其他机械性能间存在权衡,OneCurve则表现均衡。

要点

  • RCS Rainbow弯曲和屈曲抗力最高,但旋转角度和切割能力最低。
  • OneCurve切割能力最优且断裂时间较长,综合性能均衡。
  • 各器械预备后未预备根管表面无显著差异。

核心结论

  • RCS Rainbow在柔顺性与扭矩抗力间存在权衡,尺寸较大导致扭矩抗力高但柔顺性、旋转角度和切割能力降低。
  • OneCurve通过几何设计和机械性能的整合成为均衡选择。

研究设计与样本

  • 采用体视显微镜、扫描电镜和3D表面扫描评估设计,并进行冶金和机械性能测试。
  • 使用显微CT评估上颌磨牙根管预备后未预备表面。
  • 统计采用Kruskal-Wallis和单因素方差分析post hoc Tukey检验(α=5%)。

主要发现

  • 器械在活性刃长度、螺旋数和横截面设计上存在差异。
  • RCS Rainbow弯曲抗力400.5gf、屈曲抗力286gf最高,平均旋转角度529°最低(P < .05)。
  • OneCurve切割能力8.4 mm最优,断裂时间112s较长。
  • RaCe EVO断裂时间51s最短,最大扭矩1.2 N.cm、屈曲抗力174gf、弯曲抗力261gf最低(P < .05)。
  • ProTaper Ultimate扭矩1.6 N.cm和旋转角度611°最高(P < .05),弯曲载荷262gf与RaCe EVO相当(P > .05)。

临床怎么用

  • 根据临床需求选择器械:需高柔顺性可选RCS Rainbow,需均衡性能可选OneCurve。
  • 注意RCS Rainbow切割能力较低,可能影响预备效率。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: This study aimed to compare a new multicolored rotary system with four heat-treated rotary instruments using the multimethod approach. METHODS: Three-hundred instruments of RCS Rainbow, Rotate, RaCe EVO, OneCurve, and ProTaper Ultimate systems were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy, and mechanical performance (cyclic fatigue, torsional resistance, bending and buckling resistance, and cutting ability). Unprepared surfaces after canal preparation of maxillary molars were evaluated using micro-computed tomography. Kruskal-Wallis and one-way analysis of variance post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments exhibited variations in active blade length, number of spirals, and cross-sectional designs. RCS Rainbow showed specific phase transformation temperatures, highest bending (400.5gf) and buckling (286gf) resistance values, and lowest mean angle of rotation (529°) (P < .05). OneCurve exhibited superior cutting ability (8.4 mm) and longer time to fracture (112s). RaCe EVO displayed the lowest time to fracture (51s), maximum torque (1.2 N.cm), buckling (174gf), and bending resistance (261gf) values (P < .05). ProTaper Ultimate showed the highest torque (1.6 N.cm) and angle of rotation (611°) (P < .05), while its bending load (262gf) was comparable to RaCe EVO (P > .05). Rotate instrument showed intermediate values in the mechanical tests. No difference was observed regarding the unprepared canal surfaces (P > .05) CONCLUSIONS: RCS Rainbow demonstrates a trade-off between flexibility and other mechanical properties. Its dimensions exceeded those of other instruments, affording it higher torque resistance, yet concurrently reducing its flexibility, angle of rotation, and cutting ability. OneCurve stands out as a well-balanced choice by integrating geometric design and mechanical performance.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Silva EJNL, Martins JNR, Ajuz N, et al. Multimethod Analysis of a Novel Multi-coloured Heat-treated Nickel-Titanium Rotary System: Design, Metallurgy, Mechanical Properties, and Shaping Ability. J Endod. 2024. PMID: 39089614. doi:10.1016/j.joen.2024.07.011

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。