计算机辅助设计改良离体牙髓生物膜模型
本研究旨在改良一种结合人牙、计算机引导设计与3D打印的离体牙髓生物膜模型。研究比较手持切割、机械精密切割和计算机辅助引导切割三种方法,并以粪肠球菌生物膜培养21天及商业消毒处理验证模型。结果显示计算机辅助引导切割偏差更小、表面无缺陷且液密性更优,模型能区分不同消毒处理的疗效差异。
要点
- 计算机辅助引导切割制备的牙块偏差更小、表面无缺陷且液密性更优。
- 所有条件均形成高代谢活性的成熟生物膜,计算机辅助引导切割组变异最小。
- 标准2D模型中所有抗菌处理均完全根除细菌,而离体模型显示疗效不一。
核心结论
- 计算机引导切割方法为牙髓消毒治疗评估提供了更可靠、标准化和可重复的模型。
研究设计与样本
- 研究采用单根牙,分别用手持切割、机械精密切割和计算机辅助引导切割三种方法制备牙块并重新组装。
- 模型评估包括尺寸公差、表面分析、液密性及粪肠球菌生物膜21天培养(代谢检测和共聚焦显微镜)。
主要发现
- 计算机辅助引导切割与手持切割和机械精密切割相比,偏差显著更低且表面无缺陷,液密性更优。
- 所有条件下均观察到高代谢活性和活力的成熟生物膜,计算机辅助引导切割组变异最低。
- 模型验证中,所有抗菌处理在标准2D模型中完全根除细菌,而在提出的离体模型中商业处理疗效不一,从代谢活性中度降低到生物膜完全消除。
临床怎么用
- 在抗菌治疗开发中,可使用该计算机引导离体牙模型测试消毒处理,以更贴近临床地评估疗效。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVE: Most endodontic diseases are bacterium-mediated inflammatory or necrotic process induced by contaminated dental pulp. Although great advances are being performed to obtain more efficient antibacterial strategies for persistent infections, most studies lack of representative models to test their antibacterial effects and their outcomes cannot be promptly translated to clinical practice. Therefore, this study aimed to refine an ex vivo endodontic biofilm model combining human tooth, computer guided design and 3D printing to obtain a more reproducible and predictable model. METHODS: Monoradicular teeth were cut using three different methods: hand-held (HCC), mechanical precision (MPC) and computer aid guided cutting (CGC). Then, blocks were reassembled. The different model preparations were assessed in terms of dimensional tolerance, surface analysis, liquid tightness and Enterococcus faecalis biofilm development for 21 days, which was studied by metabolic assays and confocal microscopy. Then, the proposed model was validated using different commercial disinfecting treatments. RESULTS: CGC exhibited significantly lower deviation and surface without defects compared to HHC and MPC, leading to superior liquid tightness. Similarly, mature biofilms with high metabolic activity and vitality were observed in all conditions, CGC showing the lowest variation. Regarding the model validation, all antibacterial treatments resulted in the complete eradication of bacteria in the standard 2D model, whereas commercial treatments exhibited varying levels of efficacy in the proposed ex vivo model, from moderately reduction of metabolic activity to complete elimination of biofilm. CONCLUSIONS: The novel guided approach represents a more reliable, standardized, and reproducible model for the evaluation of endodontic disinfecting therapies. CLINICAL SIGNIFICANCE: During antibacterial treatment development, challenging 3D models using teeth substrates to test antibacterial treatments novel guided approach represents a more reliable, standardized, and reproducible model for the evaluation of endodontic disinfecting therapies.
引用
- Teulé-Trull M, Demiquels-Punzano E, Pérez RA, et al. Revision of ex vivo endodontic biofilm model using computer aided design. J Dent. 2024. PMID: 39084546. doi:10.1016/j.jdent.2024.105270
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。