文献速递口腔修复与种植

3D打印机、种植体替代体和角度对种植体模型代型位置精度的影响

Effect of 3D printer, implant analog and angulation on the accuracy of analog position in implant casts.
PubMed 文献 · J Dent · 2024-06-16

本研究评估3D打印机、种植体替代体系统和种植体角度对种植体模型代型位置精度的累积影响。研究使用三种DLP打印机和三种替代体系统制作90个测试模型,并与口内扫描和石膏模型对比。结论指出三者均显著影响精度,但数字工作流在短跨度病例中可达到与传统方法相似的精度。

要点

  • 3D打印机、替代体系统和种植体角度显著影响模型代型位置精度。
  • 数字工作流在短跨度种植支持病例中精度与传统方法相当。
  • 选择PRO 4K65 UV打印机和Elos替代体系统在多数情况下真度更高。

核心结论

  • 3D打印机、种植体替代体系统和种植体角度对种植体模型代型位置精度有显著影响。
  • 短跨度种植支持病例可采用数字方法复制,精度与传统方法相似。

研究设计与样本

  • 体外研究,使用坐标测量机扫描参考模型(n=1)和口内扫描仪Trios4获取第二参考数据集(n=10)。
  • 制作90个测试模型:三种DLP打印机(Max、Pro、Nex)与三种替代体系统(El、Nt、St)组合。
  • 另制作10个石膏模型作为对照,通过替代体印模制取。
  • 使用计量软件评估3D距离、局部角度和全局角度的精度,采用三因素方差分析和Tukey检验(α=0.05)。

主要发现

  • 口内扫描在3D种植体距离真度和局部角度捕捉精确度上优于石膏模型(p≤0.05)。
  • 口内扫描和3D打印引入的误差量大多相似(p>0.05)。
  • 3D打印模型精度与石膏模型相似甚至更高(p>0.05)。
  • 多数情况下,使用PRO 4K65 UV打印机和Elos替代体系统可获得更高真度(p≤0.05)。

关键数值与推荐

  • 口内扫描在3D距离真度和局部角度精确度上优于石膏模型(p≤0.05)。
  • 3D打印模型精度与石膏模型相似或更高(p>0.05)。
  • PRO 4K65 UV打印机与Elos替代体系统组合在多数情况下真度更高(p≤0.05)。

临床怎么用

  • 全数字工作流中精心选择3D打印机和种植体替代体系统可提高数字种植体模型的精度。
  • 对于短跨度种植支持病例,数字工作流可达到与传统工作流相当的精度。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: To evaluate the accumulative effect of 3D printer, implant analog systems, and implant angulation on the accuracy of analog position in implant casts. METHODS: A reference cast, presenting a case of a three-unit implant-supported prosthesis, was scanned with a coordinate measurement machine, producing the first reference data set (CMM, n = 1). The second reference data set (n = 10) was prepared using an intraoral scanner (IOS) (Trios4). Test quadrant casts were produced using three DLP type 3D printers, Max (MAX UV385), Pro (PRO 4K65 UV), and Nex (NextDent 5100), and three implant analog systems, El (Elos), Nt (Nt-trading), and St (Straumann) (n = 90). Stone casts were also produced via analog impressions (Stone, n = 10). After digitization, the accuracy of 3D distance, local angulation (angle between implants) and global angulation (angle between the implant center axis and an axis perpendicular to the global plane) was evaluated by comparing the reference (CMM, IOS), test (3D print), and control (Stone) groups using metrology software. Data were statistically analyzed using three-way ANOVA and Tukey`s tests (α = 0.05). RESULTS: IOS was truer in 3D implant distance and more precise in capturing local angulation than Stone (p ≤ 0.05). Other measurements were similar between both groups (p > 0.05). The amount of error introduced in the workflow by IOS and 3D printing was mostly similar (p > 0.05). 3D printed casts had similar or even higher accuracy than Stone group (p > 0.05). In most cases, higher trueness was achieved when using PRO 4K65 UV 3D printer and Elos implant analog system (p ≤ 0.05). CONCLUSION: 3D printer, implant analog system, and implant angulation have a significant effect on the accuracy of analog position in implant casts. Limited-span implant-supported cases could be reproduced digitally with similar accuracy as conventional methods. CLINICAL SIGNIFICANCE: A fully digital workflow with a carefully selected 3D printer and implant analog system can increase the accuracy of digitally produced implant casts with comparable accuracy to conventional workflow.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Rutkūnas V, Jegelevičius D, Gedrimienė A, et al. Effect of 3D printer, implant analog and angulation on the accuracy of analog position in implant casts. J Dent. 2024. PMID: 38885735. doi:10.1016/j.jdent.2024.105135

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。