基于AI的离体牙CBCT分辨率优化技术的构建与评估
本研究利用深度学习模型Basicvsr++对离体人牙CBCT图像进行超分辨率处理,并以Micro-CT为金标准,比较CBCT、SRCT与Micro-CT在三维重建下的根管识别差异。结果显示SRCT在硬组织体积、髓腔根管系统体积及多数根管可见长度上与Micro-CT的差异显著小于CBCT,且上颌第一磨牙MB2识别率在SRCT组为92%,高于CBCT组的72%。
要点
- 深度学习SR模型可优化离体牙CBCT根管形态显示。
- SRCT在多项参数上较CBCT更接近Micro-CT金标准。
- SRCT可能有助于上颌第一磨牙MB2的识别。
核心结论
- 所开发的深度学习模型有助于优化离体牙CBCT的根管形态,并可能有助于识别上颌第一磨牙MB2。
研究设计与样本
- 研究采用深度学习模型Basicvsr++并进行修改,数据集为171颗符合纳入标准的离体牙,其中40颗上颌第一磨牙为训练集,40颗上颌第一磨牙及91颗其他牙位牙齿为外部测试集。
- 测试集每颗牙的CBCT、SRCT和Micro-CT图像均使用Mimics Research 17.0重建,记录3组根管识别率并测量硬组织体积、髓腔和根管系统体积、根管口下可见根管长度及根管冠轴与牙长轴交角。
- 以Micro-CT测量为金标准,CBCT与SRCT图像数据采用配对样本t检验和Wilcoxon检验进行统计分析。
主要发现
- 所有测试牙图像均成功经SR程序处理。
- 在4根管上颌第一磨牙中,MB2识别率CBCT组为72%(18/25),SRCT组为92%(23/25),Micro-CT组为100%(25/25)。
- 除4根管下颌第一磨牙外,所有测试牙中SRCT与Micro-CT的硬组织体积差异显著小于CBCT与Micro-CT的差异(P < .05)。
- 所有测试牙的髓腔和根管系统体积也得到相似结果(P < .05)。
- 在大多数根管中,SRCT与Micro-CT的根管口下可见根管长度差异显著小于CBCT与Micro-CT的差异(P < .05)。
临床怎么用
- 在临床需要更精细识别根管形态时,可考虑对CBCT图像应用本研究的SR处理以辅助判断。
- 对于上颌第一磨牙MB2的识别,SRCT较CBCT显示出更高的识别率,可作为辅助手段。
局限性
- 研究仅针对离体牙,未在临床活体环境中验证。
- 训练集和外部测试集样本量有限,且仅测试了特定深度学习模型Basicvsr++的修改版本。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: In dental clinical practice, cone-beam computed tomography (CBCT) is commonly used to assist practitioners to recognize the complex morphology of root canal systems; however, because of its resolution limitations, certain small anatomical structures still cannot be accurately recognized on CBCT. The purpose of this study was to perform image super-resolution (SR) processing on CBCT images of extracted human teeth with the help of a deep learning model, and to compare the differences among CBCT, super-resolution computed tomography (SRCT), and micro-computed tomography (Micro-CT) images through three-dimensional reconstruction. METHODS: The deep learning model (Basicvsr++) was selected and modified. The dataset consisted of 171 extracted teeth that met inclusion criteria, with 40 maxillary first molars as the training set and 40 maxillary first molars as well as 91 teeth from other tooth positions as the external test set. The corresponding CBCT, SRCT, and Micro-CT images of each tooth in test sets were reconstructed using Mimics Research 17.0, and the root canal recognition rates in the 3 groups were recorded. The following parameters were measured: volume of hard tissue (V1), volume of pulp chamber and root canal system (V2), length of visible root canals under orifice (VL-X, where X represents the specific root canal), and intersection angle between coronal axis of canal and long axis of tooth (∠X, where X represents the specific root canal). Data were statistically analyzed between CBCT and SRCT images using paired sample t-test and Wilcoxon test analysis, with the measurement from Micro-CT images as the gold standard. RESULTS: Images from all tested teeth were successfully processed with the SR program. In 4-canal maxillary first molar, identification of MB2 was 72% (18/25) in CBCT group, 92% (23/25) in SRCT group, and 100% (25/25) in Micro-CT group. The difference of hard tissue volume between SRCT and Micro-CT was significantly smaller than that between CBCT and Micro-CT in all tested teeth except 4-canal mandibular first molar (P < .05). Similar results were obtained in volume of pulp chamber and root canal system in all tested teeth (P < .05). As for length of visible root canals under orifice, the difference between SRCT and Micro-CT was significantly smaller than that between CBCT and Micro-CT (P < .05) in most root canals. CONCLUSIONS: The deep learning model developed in this study helps to optimize the root canal morphology of extracted teeth in CBCT. And it may be helpful for the identification of MB2 in the maxillary first molar.
引用
- Ji Y, Chen Y, Liu G, et al. Construction and Evaluation of an AI-based CBCT Resolution Optimization Technique for Extracted Teeth. J Endod. 2024. PMID: 38848947. doi:10.1016/j.joen.2024.05.015
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。