侧面扁平化对镍钛锉扭转与循环疲劳抗性的影响
本研究比较侧面扁平化铂金V.EU锉(PL)与标准非扁平化CC Premium V.EU锉(CC)的循环疲劳和扭转抗性。循环疲劳测试在45°弯曲、6.06 mm半径的人工根管中以300 rpm旋转(每组n=15),记录失效循环次数(NCF);扭转测试以2 rpm顺时针旋转至断裂,测量最大扭矩并计算韧性和形变角。结果显示CC的NCF显著高于PL(P < .05),而扭转抗性参数无显著差异(P > .05)。结论认为侧面扁平化未改善循环或扭转抗性,且可能降低循环抗性,临床应谨慎使用。
要点
- 侧面扁平化锉的循环疲劳抗性显著低于非扁平化锉。
- 侧面扁平化对扭转抗性参数无显著影响。
- 临床使用侧面扁平化锉时应警惕循环疲劳风险。
核心结论
- 在本研究局限内,侧面扁平化未改善镍钛锉的循环抗性或扭转抗性。
- 侧面扁平化可能降低锉的循环抗性,临床应谨慎使用此类锉。
研究设计与样本
- 体外实验比较新型扁平化铂金V.EU锉(PL)与标准非扁平化CC Premium V.EU锉(CC)。
- 循环疲劳测试:45°弯曲、6.06 mm半径人工根管,300 rpm,每组n=15。
- 扭转测试:2 rpm顺时针旋转至断裂,测量最大扭矩并计算韧性和形变角。
- 每组随机选取5个碎片进行扫描电镜观察横截面和纵向。
- 采用非配对t检验,显著性水平95%。
主要发现
- CC与PL的失效循环次数(NCF)差异有统计学意义(P < .05),CC的NCF更高。
- CC与PL在扭转抗性相关参数(形变角、极限强度、韧性)上无统计学显著差异(P > .05)。
临床怎么用
- 临床使用侧面扁平化镍钛锉时需注意其循环疲劳抗性可能较低。
局限性
- 结论受本研究局限,未报告具体局限性内容。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The purpose of this study was to evaluate the effect of side flattening of cutting flutes on the cyclic resistance and torsional resistance of nickel-titanium files. METHODS: Both novel flattened Platinum V.EU (PL) and standard nonflattened CC Premium V.EU (CC) rotaries were tested. For cyclic fatigue tests, all the files were rotated in an artificial root canal with a curvature of 45° and a radius of 6.06 mm at 300 rpm (n = 15 in each group). The number of cycles to failure (NCF) was calculated. For torsional tests, the files were rotated at 2 rpm clockwise until fracture occurred. The maximum torque value at fracture was measured and the toughness and distortion angle were computed. Subsequently, 5 fragments were randomly selected in each experiment, the cross-section and longitudinal direction of the fragments were photographed using a scanning electron microscope. An unpaired t-test was performed at a significance level of 95%. RESULTS: There was a statistically significant difference in NCF between CC and PL (P < .05). CC showed higher NCF than PL. There was no statistically significant difference between CC and PL with regards to the parameters related to torsional resistance (distortion angle, ultimate strength, and toughness) (P > .05). CONCLUSION: Within the limitations of this study, side flattening of the file did not improve cyclic resistance or torsional resistance of the files. As side flattening may reduce a file's cyclic resistance, such files should be used with caution in clinical practice.
引用
- Jeong HY, Ha JH, Sigurdsson A, et al. Effects of Side Flattening on Torsional and Cyclic Fracture Resistance of Nickel-Titanium File. J Endod. 2024. PMID: 38642733. doi:10.1016/j.joen.2024.04.008
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。