连续使用往复运动锉对根管治疗成形负载的影响
这项体外研究将40个狭窄直根管分为两组,分别使用单根R-Motion锉(25/.06)和两根R-Motion锉(20/.04与25/.06)进行往复运动成形,比较根尖和冠部峰值负载。结果显示两组成形时间分别为117.3±15.1秒和123.7±7.3秒(P<.05),根尖峰值负载范围0.41-1.87 N,冠部0.38-1.03 N;除最后一次插入时多锉组根尖峰值负载显著低于单锉组(P<.01)外,两组负载相当(P>.05)。结论提示预成形可有利降低根尖峰值负载。
要点
- 在R-Motion系统中,先用较小往复锉预成形可降低根尖峰值负载。
- 单锉与多锉在根尖和冠部峰值负载上总体相当,仅末次插入有差异。
- 两组均完成成形且无锉变形或折断,多锉组用时略长。
核心结论
- 在体外使用R-Motion系统的条件下,先用较小往复锉预成形根管可有利降低离体牙根管成形中诱发的根尖峰值负载。
研究设计与样本
- 体外研究,将40个狭窄直根管分配至单锉组(RMS,R-Motion 25/.06)和多锉组(RMM,R-Motion 20/.04与25/.06)。
- 两组均采用往复运动,建立滑行通道后,RMS用单锉分两次插入至工作长度,RMM用两根锉至工作长度。
- 采用t检验和Mann-Whitney U检验在95%置信水平分析成形时间及根尖和冠部峰值负载。
主要发现
- 所有根管均在三次插入内完成成形,未观察到锉变形或折断。
- RMS和RMM成形时间分别为117.3±15.1秒和123.7±7.3秒(P<.05)。
- 各组内成形负载随锉的连续插入而增加。
- 两组根尖和冠部峰值负载范围分别为0.41-1.87 N和0.38-1.03 N。
- 除最后一次插入时RMM根尖峰值负载明显低于RMS(P<.01)外,两组根尖和冠部峰值负载相当(P>.05)。
临床怎么用
- 临床使用R-Motion系统时,可考虑先用较小往复锉预成形以降低根尖峰值负载。
- 需注意多锉操作可能略延长成形时间。
局限性
- 研究为体外实验室条件,使用离体牙狭窄直根管,结果外推需谨慎。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The purpose of this in vitro study was to investigate the apical and coronal loads generated during shaping canals with 2 successive reciprocating files in comparison to a single reciprocating file from the same system. METHODS: A total of 40 narrow and straight canals were distributed into two groups: R-Motion with single file (RMS) and R-Motion with multiple files (RMM). In both groups, the R-Motion system was used in a reciprocating motion. After establishing glide path, the RMS canals were shaped down to working length with a single file (25/.06) in two insertions while the RMM canals were shaped with two files (20/.04 and 25/.06) to the working length. The shaping time and effects of tested groups on the apical and coronal peak loads were statistically analyzed using the t-test and Mann-Whitney U test, respectively, at a 95% confidence level. RESULTS: All canals were completely shaped in three insertions and no file deformation or fracture was observed. The RMS and RMM were able to shape canals in 117.3 ± 15.1 and 123.7 ± 7.3 seconds, respectively (P < .05). Within each group, the shaping load appeared to increase with the successive insertions of the file. In both groups, the ranges of apical and coronal peak loads were 0.41-1.87 N and 0.38-1.03 N, respectively. The RMM and RMS had comparable apical and coronal peak loads (P > .05) except in the last insertion where RMM showed clearly lower apical peak load than RMS (P < .01). CONCLUSIONS: Under the current laboratory conditions using the R-Motion system, preshaping the canal with a smaller reciprocating file was shown to favorably reduce the apical peak loads induced during canal shaping of extracted teeth.
引用
- Jamleh A, Alfadley A, Tarabzoni L, et al. Impact of Sequential Use of Reciprocating Files on the Shaping Load During Root Canal Treatment. J Endod. 2023. PMID: 38092298. doi:10.1016/j.joen.2023.12.001
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。