文献速递牙体牙髓病

三维打印牙穿孔性内吸收模型不同充填技术及材料的Micro-CT评价

Evaluation of Different Techniques and Materials for Filling in 3-dimensional Printed Teeth Replicas with Perforating Internal Resorption by Means of Micro-Computed Tomography.
PubMed 文献 · J Endod · 2023-10-31

本研究在三维打印的上颌中切牙穿孔性内吸收模型中,比较两种充填技术(混合技术与增量技术)和不同材料(BCS/GP+BCR、BR/GP+BD、BCR、BD)的充填能力,通过Micro-CT测量空隙体积百分比,激光共聚焦显微镜测量表面粗糙度。结果显示BCR增量技术和BCS/GP+BCR混合技术在根尖三分之一和吸收区的充填百分比最高,BCR组的穿孔区充填质量和表面粗糙度均优于BD组。

要点

  • BCR增量技术与BCS/GP+BCR混合技术充填能力优于其他组。
  • BD组在根尖三分之一充填百分比最低(69.70±6.88)。
  • BCR组表面粗糙度(1.66±0.65 μm)低于BD组(2.51±0.89 μm)。

核心结论

  • 采用BCR的增量技术和BCS/GP+BCR的混合技术在穿孔性内吸收牙中的充填能力和质量更优。

主要发现

  • 根尖三分之一充填体积百分比:BCS/GP+BCR组89.70±5.15、BR/GP+BD组87.70±8.43、BCR组84.20±9.00均高于BD组69.70±6.88(P<.05)。
  • 内吸收区充填体积百分比:BCS/GP+BCR组96.00±2.64和BCR组95.30±2.93均高于BR/GP+BD组91.50±1.35(P<.05)。
  • 穿孔区充填质量:BCR组优于BD组(P<.001)。
  • 表面粗糙度:BCR组1.66±0.65 μm低于BD组2.51±0.89 μm(P<.05)。

临床怎么用

  • 对于穿孔性内吸收的牙体,可优先考虑采用BCR增量技术或BCS/GP+BCR混合技术进行充填,以获取更好的充填效果。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The aim of this study was to evaluate the filling ability of 2 obturation techniques in 3-dimensional (3D) printed teeth with perforating internal resorption (PIR). METHODS: A maxillary central incisor was instrumented and scanned by micro-computed tomographic (micro-CT) imaging. The 3D model was exported in the stereolithographic format and, with the aid of OrtogOnBlender software (Cícero Moraes, Sinop, SP, Brazil), a PIR in the middle third of the root canal was designed. Thirty-two replicas were printed in surgical resin and distributed into 4 groups (n = 8) according to the obturation technique and the material used: 2 groups used the hybrid technique, 1 with Bio-C Sealer (BCS; Angelus, Londrina, PR, Brazil)/gutta-percha (GP; VDW GmbH, Munich, Germany) + Bio-C Repair (BCR; Angelus, Londrina, PR, Brazil) and the other with BioRoot (BR; Septodont, Saint Maur des Fosses, France)/gutta-percha (GP) + Biodentine (BD; Septodont, Saint Maur des Fosses, France), and 2 groups used the incremental technique, 1 with BCR and the other with BD. Postobturation micro-CT imaging was performed to measure the percentage volume of voids and laser confocal microscopy to measure the surface roughness (μm) of the repair cements. Data were compared using analysis of variance and Kruskal-Wallis tests. RESULTS: Regarding the filling volume in the apical third, the BCS/GP + BCR (89.70 ± 5.15), BR/GP + BD (87.70 ± 8.43), and BCR (84.20 ± 9.00) groups showed the highest percentages compared with the BD group (69.70 ± 6.88) (P < .05). In the area of internal resorption, the BCS/GP + BCR (96.00 ± 2.64) and BCR (95.30 ± 2.93) groups showed the highest percentages compared with the BR/GP + BD group (91.50 ± 1.35) (P < .05). The BD group showed intermediate values that were sometimes similar to the BCS/GP + BCR and BCR groups and similar to the BR/GP + BD group (P > .05). Regarding the quality of the filling in the perforation area, the BCR group showed better results compared with the BD group (P < .001). Regarding roughness, the BCR group (1.66 ± 0.65) showed lower surface roughness compared with the BD group (2.51 ± 0.89) (P < .05). CONCLUSIONS: The capacity and quality of the filling in teeth with PIR were superior with the incremental technique with BCR and the hybrid technique with BCS/GP + BCR.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Torres-Carrillo AJS, Assis HC, Salazar-Gamarra RE, et al. Evaluation of Different Techniques and Materials for Filling in 3-dimensional Printed Teeth Replicas with Perforating Internal Resorption by Means of Micro-Computed Tomography. J Endod. 2023. PMID: 37918796. doi:10.1016/j.joen.2023.10.014

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。