文献速递牙体牙髓病

不同材料修复颈部外吸收腔后的断裂强度评估

Evaluation of Fracture Strength after Repair of Cervical External Resorption Cavities with Different Materials.
PubMed 文献 · J Endod · 2023-10-24

本研究采用三维有限元分析法,评估复合材料联合不同根侧修复材料(MTA、Biodentine、BioAggregate、CEM、GIC、RMGIC)修复上颌中切牙颈部外吸收腔后,在300 N、135°静态力下牙本质与修复材料的应力分布。结果显示修复显著降低牙本质应力,Biodentine、BioAggregate和CEM吸收更多力、传递至牙本质的应力更小。

要点

  • 修复颈部外吸收腔可显著降低牙本质应力。
  • Biodentine、BioAggregate和CEM比MTA、GIC、RMGIC传递更少应力至牙本质。
  • 修复材料中BioAggregate的von Mises应力最高。

核心结论

  • 修复颈部外吸收腔显著降低牙本质应力。
  • Biodentine、BioAggregate和CEM较MTA、GIC、RMGIC吸收更多力,传递至牙本质的应力更小。

研究设计与样本

  • 三维有限元分析研究,模型为上颌中切牙,模拟颈部外吸收腔及不同材料修复。

主要发现

  • 未修复颈部外吸收的模型牙本质应力最高。
  • MTA、GIC和RMGIC修复模型的牙本质von Mises应力高于Biodentine、BioAggregate和CEM修复模型。
  • 根侧修复材料的von Mises应力从高到低依次为BioAggregate、CEM、Biodentine、MTA、RMGIC、GIC。

关键数值与推荐

  • 静态力为300 N,角度为135°(与牙长轴夹角),加载于牙冠腭侧表面。

临床怎么用

  • 临床修复颈部外吸收腔时,可优先考虑Biodentine、BioAggregate或CEM以减少牙本质应力。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The aim was to evaluate the stress distributions on dentin and repair materials caused by static force applied to teeth, with cervical external root resorption (CER) after repair with different materials using finite element analysis. METHODS: This study was performed with the 3-dimensional finite element analysis method. Access cavity, root canal cavity dimensions, and supporting tissues other than cementum were modeled in the maxillary central tooth. The CER cavity was created on the labial side of the tooth model. The coronal side of the resorption cavity was restored with composite, and the radicular side with different materials (MTA, Biodentine, BioAggregate, calcium-enriched cement [CEM], glass ionomer cement [GIC], and resin-modified glass ionomer cement [RMGIC]). A static force of 300 N was applied to the palatal surface of the crown at an angle of 135° to the long axis of the tooth. The stress distributions in dentin and repair materials were analyzed. RESULTS: The highest stress in dentin was seen in the fFigmodel with unrepaired CER. In the models repaired with MTA, GIC, and RMGIC, von Mises stress values in dentin were greater than for repairs with Biodentine, BioAggregate, and CEM materials. The von Mises stress on the repair materials applied to the root were highest for the BioAggregate material. This was followed by CEM, Biodentine, MTA, RMGIC, and GIC materials, respectively. CONCLUSION: The repair of CER in the tooth significantly decreased the stress values in dentin. Biodentine, BioAggregate, and CEM absorbed more force and caused less stress to be transmitted to dentin compared to MTA, GIC, and RMGIC.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Çoban Öksüzer M, Şanal Çıkman A. Evaluation of Fracture Strength after Repair of Cervical External Resorption Cavities with Different Materials. J Endod. 2023. PMID: 37879603. doi:10.1016/j.joen.2023.10.007

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。