下颌第一磨牙中近中根管成形参数的有限元分析优化
本研究通过有限元分析探讨下颌第一磨牙独立型与汇合型中近中根管(MMC)不同成形参数对生物力学行为及寿命的影响。结果显示成形MMC会降低循环加载至失败次数(NCF),且寿命百分比与根管成形参数呈反比,30/.06组低于25/.04组,斜向加载较垂直加载进一步降低NCF。结论建议MMC成形应保守至25/.04,且独立或汇合类型决定增大根尖直径还是根管锥度。
要点
- 成形MMC会降低循环加载至失败次数(NCF),寿命百分比与成形参数呈反比。
- 30/.06成形尺寸的寿命百分比低于25/.04,独立型和汇合型模型均如此。
- 斜向加载较垂直加载降低NCF更明显,MMC成形建议保守至25/.04。
核心结论
- MMC成形应保持保守至25/.04。
- MMC为独立型或汇合型是决定需要增大根尖直径还是根管锥度的因素。
研究设计与样本
- 采用微计算机断层扫描下颌第一磨牙(含独立型MMC和汇合型MMC各一),建立有限元分析模型。
- 每种牙齿制作完整模型及5个实验模型,MMC成形参数分别为未成形、25/.04、25/.06、30/.04、30/.06。
主要发现
- 独立型和汇合型MMC模型中,成形MMC均降低循环加载至失败次数(NCF)。
- 垂直和斜向加载场景下,模型寿命百分比与根管成形参数呈反比。
- 独立型和汇合型MMC模型中,30/.06成形尺寸的寿命百分比均低于25/.04。
- 所有模型中,斜向加载较垂直加载降低NCF更多。
关键数值与推荐
- 循环加载力为50 N,施加于咬合面,分垂直和斜向两种场景。
- 比较指标为循环加载至失败次数(NCF)及寿命百分比。
临床怎么用
- MMC成形应保守至25/.04。
- 当需要更大成形参数时,需根据MMC为独立型或汇合型决定增大根尖直径还是根管锥度。
局限性
- 原文未述局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: This study investigated the effect of shaping parameters of 2 different configurations of middle mesial canals (MMCs) on the biomechanical behavior and life span of a mandibular first molar using finite element analysis (FEA). METHODS: A mandibular molar with an independent MMC and another with a confluent MMC were scanned via micro-computed tomography, and FEA models were produced. For each tooth, an intact model and 5 experimental models were produced that differed by parameters of how the MMC was shaped: unshaped MMC, 25/.04, 25/.06, 30/.04, and 30/.06. Cyclic loading of 50 N was applied on the occlusal surface in vertical and oblique scenarios, and the number of cycles until failure (NCF) was compared with the intact models. In addition, mathematical analyses evaluated the stress distribution patterns and calculated maximum von Mises and maximum principal stresses. RESULTS: For both the independent and confluent MMC models, shaping the MMC reduced the NCF. The lifelog percentage of models was inversely proportional with radicular shaping parameters during the vertical and oblique loading scenarios. The shaping size of 30/.06 resulted in lower lifelog percentage than the cases with shaping size of 25/.04 in both of the independent and confluent MMC models. For all models, oblique loading reduced NCF more than vertical loading. CONCLUSION: Shaping the MMC should be kept as conservative as 25/.04. Also, whether the MMC is independent or confluent is a deciding factor in whether to increase the apical diameter or the root canal taper when larger shaping parameters are needed.
引用
- Nawar NN, Elkholy MMA, Ha WN, et al. Optimum Shaping Parameters of the Middle Mesial Canal in Mandibular First Molars: A Finite Element Analysis Study. J Endod. 2023. PMID: 36965769. doi:10.1016/j.joen.2023.03.007
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。