文献速递牙体牙髓病

电火花加工三种旋转器械的多方法分析

Multimethod analysis of three rotary instruments produced by electric discharge machining technology.
PubMed 文献 · Int Endod J · 2023-04-25

本研究比较HyFlex EDM、Neoniti、EDMax三种电火花加工旋转器械与热处理ProTaper Gold系统在设计、冶金学、机械性能和成形能力方面的差异。结果显示器械几何形态和相变温度影响机械测试结果,但不影响成形能力;各组未预备根管面积无统计学差异。

要点

  • 所有器械均为不对称刃、无径向平面、镍钛比接近等原子比。
  • Neoniti与HyFlex EDM在所有机械测试中结果相似(p > .05)。
  • 各系统未预备根管面积无统计学差异(p > .05)。

核心结论

  • 器械的几何形态和相变温度影响机械测试结果,但不影响成形能力。

研究设计与样本

  • 体外研究,每组n = 58,比较HyFlex EDM(25/~)、Neoniti(25/.06)、EDMax(25/.06)和ProTaper Gold(25/.08v)的设计、冶金学和机械性能。
  • 使用微CT计算下颌磨牙近中颊、近中舌和远中根管预备后未预备根管面积,每组15个根管。

主要发现

  • 所有器械均为不对称刃、无径向平面、无明显缺陷、镍钛比接近等原子比,但横截面设计、尖端几何和表面外观不同。
  • 器械在21°C呈马氏体排列,在体温下呈奥氏体加R相混合,但相变温度曲线不同。
  • Neoniti和HyFlex EDM在所有机械测试中结果相似(p > .05)。
  • EDMax和ProTaper Gold在断裂时间(p = .841)、最大弯曲载荷(p = .729)和切割能力(p = .985)方面相似。
  • ProTaper Gold的抗断裂扭矩最高(p < .001),HyFlex EDM的抗屈曲能力最低(p < .001)。

关键数值与推荐

  • 统计方法采用单因素方差分析事后Tukey检验和Kruskal-Wallis事后Dunn检验(α = 5%)。

局限性

  • 原文未述局限性

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIM: This study aimed to compare three rotary instruments produced by the EDM process with the heat-treated ProTaper Gold system regarding design, metallurgy, mechanical properties and shaping ability. METHODOLOGY: HyFlex EDM (25/~), Neoniti (25/.06), EDMax (25/.06) and ProTaper Gold (25/.08v) instruments (n = 58 per group) were compared regarding design, metallurgy and mechanical performance. Unprepared canal areas were calculated for each system after preparation of mesiobuccal, mesiolingual and distal canals of mandibular molars (15 canals per group) using micro-CT technology. Statistical analyses were performed using One-way anova post-hoc Tukey and Kruskal-Wallis post-hoc Dunn's tests (α = 5%). RESULTS: All instruments had asymmetrical blades, no radial lands, no major defects and almost equiatomic nickel/titanium ratios, but different cross-section designs, tip geometries and surface appearances. Although instruments had distinct transformation temperature curves, they showed crystallographic martensitic arrangement at 21°C and mixed austenite plus R-phase at body temperature. Neoniti and HyFlex EDM showed similar results in all mechanical tests (p > .05), while EDMax and ProTaper Gold had similar time to fracture (p = .841), maximum bending load (p = .729), and cutting ability (p = .985). ProTaper Gold showed the highest torque to failure (p < .001) and HyFlex EDM had the lowest buckling resistance (p < .001). Mean percentages of unprepared canal areas ranged from 20.4% to 25.7% in the mesial canals, and from 20.8% to 26.2% in the distal canal, with no statistical differences among systems (p > .05). CONCLUSIONS: Instruments' geometry and phase transformation temperatures influenced the results of the mechanical tests, but not their shaping ability.

来源:Int Endod J,查看原文。版权归原作者所有。

引用

  1. Silva EJNL, Ajuz NC, Martins JNR, et al. Multimethod analysis of three rotary instruments produced by electric discharge machining technology. Int Endod J. 2023. PMID: 36942476. doi:10.1111/iej.13915

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。