文献速递口腔修复与种植口腔颌面外科

定制CAD/CAM合成骨移植用于牙槽嵴增量:3年随访的回顾性临床研究

Custom-made computer-aided-design/ computer-assisted-manufacturing (CAD/CAM) synthetic bone grafts for alveolar ridge augmentation: A retrospective clinical study with 3 years of follow-up.
PubMed 文献 · J Dent · 2022-10-12

本研究回顾性报告了26例患者使用定制CAD/CAM合成羟基磷灰石/β-磷酸三钙(HA/β-TCP)骨移植进行牙槽嵴增量,8个月后植入种植体并随访3年。结果显示平均垂直和水平骨增量分别为2.10 mm(±0.35)和2.96 mm(±0.45),3年种植体冠成功率为92.0%,种植体周围边缘骨丧失为0.7 mm(±0.19)。作者认为该技术可用于小范围骨缺损的再生,但需进一步研究验证。

要点

  • 26例患者中,25/26(96.1%)的移植骨与骨缺损适配良好。
  • 术后即刻并发症包括疼痛和肿胀(2/26,7.6%)及移植骨暴露(3/26,11.5%)。
  • 8个月时平均垂直和水平骨增量分别为2.10 mm(±0.35)和2.96 mm(±0.45)。

核心结论

  • 定制CAD/CAM合成HA/β-TCP贴面骨移植可实现牙槽嵴小范围垂直和/或水平缺损的重建,使种植体植入成为可能,3年后种植体冠成功率高。
  • 作者认为需要进一步研究来验证该技术。

研究设计与样本

  • 回顾性临床研究,纳入26例接受定制CAD/CAM合成HA/β-TCP贴面骨移植进行牙槽嵴增量的患者,随访3年。

主要发现

  • 术中25/26(96.1%)的移植骨与骨缺损适配良好。
  • 术后即刻并发症为疼痛和肿胀(2/26,7.6%)及移植骨暴露(3/26,11.5%),其中1例暴露导致感染、移植骨移除和手术失败。
  • 8个月时平均垂直骨增量为2.10 mm(±0.35),平均水平骨增量为2.96 mm(±0.45)。
  • 植入25枚种植体并完成单冠修复,3年后所有种植体均在功能状态。
  • 3年种植体冠成功率为92.0%,种植体周围边缘骨丧失为0.7 mm(±0.19)。

关键数值与推荐

  • 8个月时平均垂直骨增量2.10 mm(±0.35),平均水平骨增量2.96 mm(±0.45)。
  • 3年种植体冠成功率为92.0%,种植体周围边缘骨丧失为0.7 mm(±0.19)。

临床怎么用

  • 作者认为定制CAD/CAM合成HA/β-TCP贴面骨移植可作为种植体植入前小范围骨缺损再生的一种选择。

局限性

  • 原文未报告局限性。
  • 作者在结论中指出需要进一步研究来验证该技术。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

PURPOSE: To report on the results obtained with computer-aided-design/ computer-assisted-manufacturing (CAD/CAM) custom-made synthetic hydroxyapatite/beta-tricalcium-phosphate (HA/beta-TCP) bone grafts in alveolar ridge augmentation for dental implant placement. METHODS: The procedure included: (1) cone-beam computed tomography (CBCT) of the bone defect; (2) virtual design of the custom-made onlay bone grafts; (3) milling of grafts from a pre-formed block of synthetic HA/beta-TCP; and (4) bone reconstructive surgery. Implants were placed 8 months later. The patients were followed for 3 years. The study outcomes were: (1) intra- and immediate post-operative complications; (2) 8-month vertical and horizontal bone gain; (3) implant survival; (4) implant-crown success; and (5) peri-implant marginal bone loss (MBL). RESULTS: Twenty-six patients underwent ridge augmentation with custom-made CAD/CAM HA/beta-TCP onlay grafts. Eight months later, these patients were rehabilitated with dental implants. During surgery, 25/26 (96.1%) of the grafts adapted well to the bone defect. Immediate post-operative complications were pain and swelling (2/26 patients: 7.6%), and bone graft exposure (3/26: 11.5%); one exposure led to infection, removal of the graft, and failure of the procedure. Excellent integration of the other grafts was observed 8 months after the regenerative procedure, with mean vertical and horizontal bone gains of 2.10 mm (± 0.35) and 2.96 mm (± 0.45), respectively. Twenty-five implants were placed and restored with single crowns. Three years later, all implants were in function. The 3-year implant crown success rate and peri-implant MBL were 92.0% and 0.7 mm (±0.19), respectively. CONCLUSIONS: With custom-made CAD/CAM synthetic HA/beta-TCP onlay grafts reconstruction of small vertical and/or horizontal defects of the alveolar ridge was obtained; this enabled implant placement, with high implant-crown success rate after 3 years. Further studies are needed to validate this technique. STATEMENT OF CLINICAL RELEVANCE: Custom-made CAD/CAM synthetic HA/beta-TCP onlay grafts may represent an option for regeneration of small bone defects prior to implant placement.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Mangano C, Luongo G, Luongo F, et al. Custom-made computer-aided-design/ computer-assisted-manufacturing (CAD/CAM) synthetic bone grafts for alveolar ridge augmentation: A retrospective clinical study with 3 years of follow-up. J Dent. 2022. PMID: 36241044. doi:10.1016/j.jdent.2022.104323

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。