文献速递牙体牙髓病口腔颌面外科

靶向牙髓显微外科中环钻切除根端的应力分布:有限元分析

Stress Distribution on Trephine-Resected Root-end in Targeted Endodontic Microsurgery: A Finite Element Analysis.
PubMed 文献 · J Endod · 2022-10-19

该有限元分析基于锥形束CT数据构建靶向牙髓显微外科治疗的上颌中切牙模型,比较平坦与弯曲根端、有无根尖骨移植及正常与根管充填对照在咬合负载下的应力分布。结果显示根端切除形态与根尖骨支撑明显影响咬合应力模式,弯曲根端应力集中于其周缘,骨移植可缓解唇侧颈部应力。作者据此建议靶向牙髓显微外科切除根端应磨平并植骨以分散咬合负载应力。

要点

  • 弯曲根端周缘平均应力值显著高于平坦根端(P < .05),有根尖骨支撑时尤为明显(P < .05)。
  • 骨移植后最大应力集中从唇侧颈部根面转移至根尖,提示颈部根区应力缓解与分散。
  • 作者建议靶向牙髓显微外科切除根端应磨平并植骨以分散咬合负载应力。

核心结论

  • 上颌中切牙咬合应力模式明显受根端切除形态与根尖骨支撑影响。
  • 环钻切除的弯曲根端应力模式集中于其周缘。
  • 弯曲与平坦根端均有唇侧颈部应力,骨移植可使其缓解。
  • 作者建议靶向牙髓显微外科切除根端应磨平并植骨以分散咬合负载应力。

研究设计与样本

  • 有限元分析模型基于一例靶向牙髓显微外科治疗的上颌中切牙的锥形束CT数据构建。
  • 模型包括平坦与弯曲根端切除、有无根尖骨移植,以及正常与根管充填对照。
  • 正中咬合时轴向力以120°角作用于近中与远中舌侧边缘嵴,侧方运动时在正中咬合基础上加力,边缘咬合时轴向力作用于切缘。

主要发现

  • 正常与根管充填对照中,咬合应力分布于唇侧与腭侧根面,集中于唇侧颈部区域,并在根尖处最大。
  • 根端切除模型中咬合负载使应力集中于唇侧颈部区域,骨移植后最大应力集中转移至根尖。
  • 有根尖骨移植的模型根端应力模式分布更广,弯曲根端尤其在没有根尖骨支撑时显示应力集中弧。
  • 根端周缘平均应力值弯曲根端显著高于平坦根端(P < .05),有根尖骨支撑时尤为明显(P < .05)。

临床怎么用

  • 作者建议靶向牙髓显微外科切除根端应磨平并植骨以分散咬合负载应力。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: This study aimed to determine if stress distribution from occlusal loads after targeted endodontic microsurgery (TEMS) differed for trephine-resected flat and curved root-ends, with and without bone graft. METHODS: Finite element analysis models were constructed from cone-beam computed tomography data of a TEMS-treated maxillary central incisor. Models included flat and curved resected root-ends, with and without apical bone graft, and normal or root canal filled controls. In centric occlusion, axial force was directed on mesial and distal lingual marginal ridges at 120° angle. For lateral excursion, additional mesiodistal forces were applied from centric occlusion. For edge biting, axial force was directed on the incisal edge. Under occlusal loads, stress distribution patterns on tooth and root-end circumference were analyzed. RESULTS: In normal and root filled controls, occlusal stress was distributed on labial and palatal root surfaces, concentrated in the labial cervical area, and maximized at the apex. For resected root-ends, occlusal loads concentrated stress on the labial cervical area. With bone graft, maximum stress concentration shifted to the apex, which implied stress relief and dispersion from the cervical root area. Stress patterns on the root-end were more widely spread in models with apical bone graft, whereas curved root-end showed stress concentrating arc especially when without apical bone support. The mean stress values on root-end circumference were significantly higher in curved than flat root-end (P < .05), especially with apical bone support (P < .05). CONCLUSIONS: Occlusal stress patterns on a maxillary central incisor were markedly affected by root-end resection configuration and apical bone support. Trephine-resected curved root-end had stress pattern concentrated on its circumference. Curved and flat root-ends had labial cervical stress that was relieved by bone graft. TEMS resected root-ends should be flattened and bone grafted to disperse stress from occlusal loads.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Yoo YJ, Perinpanayagam H, Kim M, et al. Stress Distribution on Trephine-Resected Root-end in Targeted Endodontic Microsurgery: A Finite Element Analysis. J Endod. 2022. PMID: 36270576. doi:10.1016/j.joen.2022.10.005

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。