动态导航用于单牙间隙种植体植入:一项临床前初步研究
本研究在五对人工颌骨上制造四个单牙间隙(FDI 16、25、36、44区),利用动态导航系统(DNS)进行数字化种植规划,比较规划种植体位置(PIP)与转移种植体位置(TIP)的偏差。结果显示入口点二维偏差均值0.78±0.45 mm,根尖三维偏差1.08±0.50 mm,根尖垂直偏差0.32±0.22 mm,角度偏差中位数2.81±2.29°;不同象限间根尖三维、根尖垂直和角度偏差存在统计学显著差异(p<0.05)。作者认为该dCAIS在体外单牙间隙中似乎能提供满意的TIP结果,并建议在DNS软件规划时保留超过2 mm的安全距离。
要点
- 入口点二维偏差均值0.78±0.45 mm,根尖三维偏差1.08±0.50 mm。
- 根尖垂直偏差0.32±0.22 mm,角度偏差中位数2.81±2.29°。
- 不同象限间根尖三维、根尖垂直和角度偏差有统计学显著差异(p<0.05)。
核心结论
- 使用所研究的dCAIS在体外单牙间隙中似乎能提供满意的TIP结果。
- 由于存在记录的偏差,在DNS软件中进行种植规划时应保留超过2 mm的安全距离。
- 所研究的DNS似乎能可靠地转移PIP,在体外具有可接受的偏差。
研究设计与样本
- 通过注塑技术制造五对人工颌骨(n=5),每对含四个单牙间隙,位于FDI 16、25、36和44区。
- 拍摄锥形束CT(CBCT)后,使用动态导航系统(DNS,Navident,ClaroNav,Toronto,Canada)对二十枚种植体(n=20)进行数字化种植规划。
- 在引导钻孔和手动植入种植体后拍摄术后CBCT,由DNS软件计算偏差。
- 统计学分析显著性水平设为p<0.05。
主要发现
- 种植体入口点二维偏差均值为0.78±0.45 mm(范围:0.10-1.63 mm)。
- 种植体根尖三维偏差为1.08±0.50 mm(范围:0.33-2.10 mm),根尖垂直偏差为0.32±0.22 mm(范围:0.02-0.90 mm)。
- 角度偏差中位数为2.81±2.29°(范围:0.56-9.58°)。
- 比较I-IV象限,根尖三维、根尖垂直和角度偏差存在统计学显著差异(p<0.05)。
关键数值与推荐
- 规划种植体位置(PIP)与转移种植体位置(TIP)的偏差通过DNS软件计算。
- 入口点偏差为二维(2D),根尖偏差为三维(3D)和垂直(V),角度偏差以度(°)表示。
- 统计学显著性水平设为p<0.05。
临床怎么用
- 作者建议在DNS软件中进行种植规划时,应保留超过2 mm的安全距离。
- 所研究的DNS在体外似乎能可靠地转移PIP,具有可接受的偏差。
局限性
- 本研究为临床前初步研究,在体外进行。
- 样本为五对人工颌骨(n=5)和二十枚种植体(n=20)。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: To compare the planned (PIP) and transferred implant position (TIP) after dental implant placement in single-tooth gaps utilizing dynamic computer-assisted implant surgery (dCAIS). METHODS: Five pairs of artificial jaws (n = 5) with four single tooth gaps in FDI (Fédération Dentaire Internationale) regions 16, 25, 36 and 44 were manufactured via injection molding technique. Cone beam computed tomographies (CBCTs) were made and digital implant planning of twenty implants (n = 20) was performed with a dynamic navigation system (DNS, Navident, ClaroNav, Toronto, Canada). After guided drilling and manual implant placement, post-operative CBCTs were made. Global deviations at entry point (two-dimensional, 2D), apex (three-dimensional, 3D), apex (vertical, V) and angulation (in degrees, °) were calculated by DNS software. For statistical analysis, level of significance was set to p < 0.05. RESULTS: Mean deviation at the implants entry point (2D) was 0.78 ± 0.45 mm (range: 0.10-1.63 mm). For the implants apex (3D) and the implants apex (V) deviations were 1.08 ± 0.50 mm (range: 0.33-2.10 mm) and 0.32 ± 0.22 mm (range: 0.02-0.90 mm), respectively. The median angular deviation (°) was 2.81 ± 2.29° (range: 0.56-9.58°). Statistically significant differences (p < 0.05) were found regarding apex (3D), apex (V), and angulation (°) comparing I.-IV. quadrants. CONCLUSIONS: Using the investigated dCAIS seems to provide satisfactory results regarding TIP in single-tooth gaps in vitro. Due to documented deviations, a safety distance of more than 2 mm should be respected while implant planning in DNS software. CLINICAL SIGNIFICANCE: The investigated DNS seems to be reliant in transferring PIP with acceptable deviations in vitro.
引用
- Böse MWH, Beuer F, Schwitalla A, et al. Dynamic navigation for dental implant placement in single-tooth gaps: A preclinical pilot investigation. J Dent. 2022. PMID: 35995082. doi:10.1016/j.jdent.2022.104265
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。