采用微粒子图像测速技术对汇合根管内冲洗流计算流体动力学模型进行实验验证
本研究采用聚二甲基硅氧烷微芯片汇合根管模型,以微粒子图像测速技术测量侧方开口针头冲洗流速场,并与FLUENT有限体积法层流与湍流模拟结果比较。结果显示实验与计算流体动力学预测的流型、等速线、矢量图和速度剖面高度一致,层流与湍流模型间无相关差异;作者认为层流计算流体动力学建模可可靠预测类似区域内的流动。
要点
- 微粒子图像测速实验与计算流体动力学预测的流型和速度剖面高度一致。
- 侧方开口针头置于汇合处末端3 mm处,流速为0.017和0.1 ml/s。
- 层流与湍流模型所得结果间未见相关差异,层流建模可靠。
核心结论
- 结果显示层流计算流体动力学建模可可靠预测类似区域内的流动。
研究设计与样本
- 采用聚二甲基硅氧烷制成的汇合根管微芯片,以微粒子图像测速技术分析侧方开口针头冲洗的流速场。
主要发现
- 整体流型、等速线图、矢量图及速度剖面在微粒子图像测速实验与计算流体动力学预测数据之间高度一致。
- 所用层流与湍流流动模型所得结果之间未见相关差异。
关键数值与推荐
- 侧方开口针头置于距汇合处末端3 mm处,流速为0.017和0.1 ml/s。
- 计算流体动力学数值模拟采用有限体积商业代码FLUENT,涵盖层流与湍流两种流态。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIM: This study aimed to experimentally validate a computational fluid dynamics (CFD) model, using micro-particle image velocimetry (micro-PIV) measurements of the irrigation flow velocity field developed in confluent canals during irrigation with a side-vented needle. METHODOLOGY: A microchip with confluent canals, manufactured in polydimethylsiloxane was used in a micro-PIV analysis of the irrigation flow using a side-vented needle placed 3 mm from the end of the confluence of the canals. Velocity fields and profiles were recorded for flow rates of 0.017 and 0.1 ml/s and compared with those predicted in CFD numerical simulations (using a finite volume commercial code - FLUENT) for both laminar and turbulent regimes. RESULTS: The overall flow pattern, isovelocity and vector maps as well as velocity profiles showed a close agreement between the micro-PIV experimental and CFD predicted data. No relevant differences were observed between the results obtained with the laminar and turbulent flow models used. CONCLUSIONS: Results showed that the laminar CFD modelling is reliable to predict the flow in similar domains.
引用
- Rito Pereira M, Silva G, Semiao V, et al. Experimental validation of a computational fluid dynamics model using micro-particle image velocimetry of the irrigation flow in confluent canals. Int Endod J. 2022. PMID: 36040378. doi:10.1111/iej.13827
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。