文献速递口腔修复与种植

全个性化无基台氧化锆种植冠在新型种植体-冠界面上的机械稳定性

Mechanical stability of fully personalized, abutment-free zirconia implant crowns on a novel implant-crown interface.
PubMed 文献 · J Dent · 2022-04-05

研究将48颗种植体分为4组,比较个性化无基台氧化锆CAD-CAM冠与常规基台界面的失败载荷和失败模式。经热机械老化后静态加载至失败,平均失败载荷在1332 N至1601 N之间,仅无基台组与Ti-Base-2组间差异有统计学意义。无基台组失败载荷与多数常规界面相似。

要点

  • 所有样本均通过热机械老化,平均失败载荷1332 N(无基台组)至1601 N(Ti-Base-2组)。
  • 无基台组与Ti-Base-2组失败载荷差异有统计学意义(p<0.05),其余组间无差异。
  • 无基台组主要失败模式为种植体连接上方冠折(75%)。

核心结论

  • 全个性化无基台氧化锆CAD-CAM冠的种植体-冠界面失败载荷与采用预制或中心制作基台的常规种植体-基台界面相似(Ti-Base-2组除外)。

研究设计与样本

  • 体外研究,48颗种植体按种植体-基台界面设计分为4组(每组n=12),均修复为螺丝固位氧化锆CAD-CAM磨牙冠。

主要发现

  • 平均失败载荷:无基台组1332 N,Ti-Base-2组1601 N,两组差异有统计学意义(p<0.05)。
  • 其余组间失败载荷无差异。
  • 主要失败模式:无基台组为种植体连接上方冠折(75%),Cen-Abut-Zr组为种植体颈部下方基台折断(83%),Ti-Base-1/Ti-Base-2组为冠折而基台完整(100%)。

临床怎么用

  • 作者指出,新型种植体连接简化了全瓷种植修复的数字工作流程。
  • 作者指出,该种植体-冠界面的特定设计允许在院内和技工室制作全个性化无基台氧化锆种植冠,无需预制基台或中心制作。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: To test the failure load and failure mode of a novel implant-crown interface specifically designed for the fabrication of fully personalized, abutment-free monolithic zirconia CAD-CAM crowns compared to conventional implant-abutment interfaces involving prefabricated or centrally manufactured abutments for zirconia CAD-CAM crowns. METHODS: Implants (N=48) were divided into groups (n=12) according to different implant-abutment interface designs: (1) internal implant connection with personalized, abutment-free CAD-CAM crowns (Abut-Free-Zr), (2) internal conical connection with customized, centrally manufactured zirconia CAD-CAM abutments (Cen-Abut-Zr), (3) prefabricated titanium base abutments from manufacturer 1 (Ti-Base-1), (4) additional prefabricated titanium base abutments from manufacturer 2 (Ti-Base-2). All specimens were restored with a screw-retained monolithic zirconia CAD-CAM molar crown and subjected to thermomechanical aging (1.200.000 cycles, 49 N, 1.67 Hz, 30° angulation, thermocycling 5-50°C). Static load until failure was applied in a universal testing machine. Failure modes were analyzed descriptively under digital microscope. Mean failure load values were statistically analyzed at a significance level of p<0.05. RESULTS: All specimens survived thermomechanical aging. The mean failure loads varied between 1332 N (Abut-Free-Zr) and 1601 N (Ti-Base-2), difference being significant between these groups (p<0.05). No differences between the other groups were seen. The predominant failure mode per group was crown fracture above implant connection (Abut-Free-Zr, 75%), abutment fracture below implant neck (Cen-Abut-Zr, 83%), crown fracture leaving an intact abutment (Ti-Base-1/Ti-Base-2 100%). CONCLUSIONS: Implant-crown interface with fully personalized, abutment-free monolithic CAD-CAM zirconia crowns exhibited similar failure loads as conventional implant-abutment interfaces (except group Ti-Base-2) involving CAD-CAM crowns with prefabricated or centrally manufactured abutment. CLINICAL SIGNIFICANCE: The new implant connection simplifies the digital workflow for all-ceramic implant reconstructions. The specific design of the implant-crown interface allows the fabrication of fully personalized, abutment-free zirconia implant crowns both in-house and in-laboratory without the need of a prefabricated abutment or central manufacturing.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Hjerppe J, Jung RE, Hämmerle CH, et al. Mechanical stability of fully personalized, abutment-free zirconia implant crowns on a novel implant-crown interface. J Dent. 2022. PMID: 35395344. doi:10.1016/j.jdent.2022.104121

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。