文献速递牙体牙髓病

使用低成本3D打印机制作导板进行开髓洞形预备

Guided Access Cavity Preparation Using Cost-Effective 3D Printers.
PubMed 文献 · J Endod · 2022-04-11

这项体外研究评估了四种桌面3D打印机制作导板时用于引导牙髓开髓的准确性和精密度。每种导板在模型牙上重复开髓10次,钻针尖端与规划位置的绝对偏差均值为0.31至0.68 mm,四组间存在统计学显著差异(F3,36=10.67,P<.05),其中Form3组在冠方和根方的轴向偏差最准确、最精密。所有测试打印机均能制作导板实现高精度开髓,支持试用低成本3D打印机进行引导牙髓开髓,并需要对牙髓钙化牙进行进一步临床研究。

要点

  • 四种桌面3D打印机所制导板引导开髓的平均偏差为0.31至0.68 mm。
  • 四组间偏差存在统计学显著差异(F3,36=10.67,P<.05)。
  • Form3组在冠方和根方的轴向偏差最准确、最精密。

核心结论

  • 所有测试的打印机均能制作导板实现高精度的人工牙髓管开髓,支持试用低成本3D打印机进行引导牙髓开髓,并需要对牙髓钙化牙进行进一步临床研究。

研究设计与样本

  • 体外研究:使用规划软件在模型上设计引导牙髓开髓导板,四种不同3D打印机各制作一个相同导板,每个导板由同一操作者重复开髓10次,扫描后以最佳拟合对齐自动计算钻针基部和尖端的绝对偏差。

主要发现

  • 钻针规划位置与实际位置之间的平均距离较低,范围为0.31至0.68 mm。
  • 四组间存在统计学显著差异(F3,36=10.67,P<.05)。
  • 事后比较显示Form2组与Form3组和Carbon组存在显著差异(分别为P<.05和P<.05)。
  • Form3组在冠方和根方均获得最准确和最精密的轴向偏差。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The purpose of this in vitro study was to evaluate the accuracy and precision of desktop 3D printers when fabricating stents for guided endodontics. METHODS: A stent was designed using planning software for guided endodontic access on a typodont model. Four different 3D printers were used to fabricate an identical stent, one per printer. Each stent was then used to gain access to the artificial endodontic canal on a typodont tooth and was repeated 10 times per stent by the same operator. Each of the accessed typodont teeth were scanned by a reference scanner and then imported into the inspection software. Inspection software used a best-fit alignment to automatically calculate absolute deviation at the base and tip of the bur. RESULTS: The mean distances between the planned and actual positions of the bur were low, ranging from 0.31 to 0.68 mm. Statistically significant differences were found among the 4 groups (F3,36 = 10.67, P < .05). Post hoc comparison revealed that Group Form2 significantly varied from Groups Form3 and Carbon (P < .05 and P < .05, respectively). Group Form3 obtained the most accurate and most precise axial deviations both coronally and apically. CONCLUSIONS: All of the printers tested produced stents for guided access that allowed for a high level of accuracy in obtaining access to the artificial endodontic canal, which would justify the trial of cost-effective 3D printers for guided endodontic access and necessitates further clinical research on teeth with pulp canal obliteration.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Koch GK, Gharib H, Liao P, et al. Guided Access Cavity Preparation Using Cost-Effective 3D Printers. J Endod. 2022. PMID: 35421408. doi:10.1016/j.joen.2022.04.005

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。