开髓洞形预备对牙本质保存、生物力学性能及器械成形效果的影响:一项微计算机断层扫描研究
本研究以48颗离体上、下颌第一恒磨牙为对象,比较缩窄开髓洞形(CEC)与传统开髓洞形(TEC)在牙本质保存、生物力学性能和器械成形效果上的差异。微CT显示CEC组牙冠牙本质及牙槽嵴以上颈周牙本质(PCD)的体积和厚度减少显著低于TEC组(P<.05),而牙槽嵴以下PCD两组无差异(P>.05);两组器械成形效果各项指标均无差异(P>.05)。三维有限元分析显示CEC可有效降低咬合面及颈部区域的最大von Mises应力和应力集中面积。
要点
- CEC组牙冠牙本质及牙槽嵴以上PCD的体积和厚度减少显著低于TEC组(P<.05)。
- 两组牙槽嵴以下PCD及所有器械成形效果指标均无显著差异(P>.05)。
- CEC可有效降低咬合面及颈部区域的最大von Mises应力和应力集中面积。
核心结论
- CEC保留了更多牙冠牙本质和牙槽嵴以上PCD,从而降低咬合面及颈部区域的应力集中。
- 在使用ProGlider和WaveOne Gold器械进行根管成形的前提下,CEC对器械成形效果无显著不良影响。
研究设计与样本
- 离体牙实验:选取48颗完整离体上、下颌第一恒磨牙,按牙位解剖匹配后分为CEC组和TEC组(每组n=12)。
- 预备前后行微计算机断层扫描(micro-CT)评估牙本质保存与器械成形效果。
- 基于微CT影像构建CEC与TEC模型,施加2种不同静载荷进行三维有限元分析。
主要发现
- CEC组牙冠牙本质及牙槽嵴以上PCD的体积和厚度减少显著低于TEC组(P<.05)。
- 两组牙槽嵴以下PCD的体积和厚度减少无差异(P>.05)。
- 两组根管体积和表面积、未预备表面积百分比、根管偏移及中心定位比、危险区根管壁厚度均无差异(P>.05)。
- 与TEC相比,CEC有效降低了咬合面及颈部区域的最大von Mises应力和应力集中面积。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The purpose of this study was to evaluate the influence of a contracted endodontic cavity (CEC) on dentin preservation, biomechanical property, and instrumentation efficacy of first permanent molars in comparison with a traditional endodontic cavity (TEC). METHODS: Forty-eight extracted intact maxillary and mandibular first molars were selected and scanned by micro-computed tomographic (micro-CT) imaging. Each tooth type was anatomically matched and assigned to the CEC group or the TEC group (n = 12). After root canal instrumentation with the ProGlider (Dentsply Maillefer, Ballaigues, Switzerland) and WaveOne Gold (Dentsply Maillefer), the specimens were scanned by micro-CT again. Pre- and postpreparation micro-CT imaging was used to evaluate the dentin preservation and instrumentation efficacy. The results on volume and thickness reduction in the coronal dentin and pericervical dentin (PCD), root canal volume and surface area, percentage of unprepared surface area, canal transportation and centering ratio, and canal wall thickness in the "danger zone" were measured and analyzed with the Shapiro-Wilk and independent sample t tests. Based on micro-CT imaging of maxillary and mandibular first molars, CEC and TEC models were constructed on the intact tooth, and 2 different static loads were applied to the occlusal load points. The stress distribution patterns and von Mises stress on the occlusal surface and cervical region were assessed by 3-dimensional finite element analysis. RESULTS: The CEC had a significantly lower volume and thickness reduction of coronal dentin and PCD above the alveolar crest compared with the TEC group (P < .05), whereas no difference was observed in PCD below the alveolar crest between the 2 groups (P > .05). There was no difference regarding all instrumentation efficacy outcomes (root canal volume and surface area, percentage of unprepared surface area, canal transportation and centering ratio, and canal wall thickness) in the danger zone between the 2 groups (P > .05). The CEC effectively reduced the maximum von Mises stress and stress concentration area on the occlusal surface and cervical region compared with the TEC. CONCLUSIONS: The CEC preserved more coronal dentin and PCD above the alveolar crest and thus reduced stress concentration on the occlusal surface and cervical region. The CEC had no significant adverse effects on the instrumentation efficacy compared with the TEC given that the instrumentation procedures were performed with ProGlider and WaveOne Gold files.
引用
- Peng W, Zhou X, Gao Y, et al. Effect of Access Cavity Preparation on Dentin Preservation, Biomechanical Property, and Instrumentation Efficacy: A Micro-Computed Tomographic Study. J Endod. 2022. PMID: 35227729. doi:10.1016/j.joen.2021.12.012
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。