自体移植磨牙应力分布的有限元分析
本研究通过有限元分析构建7种自体移植牙情境模型,在200 N沿牙长轴咬合负载下计算牙本质与周围骨的最大von Mises应力。结果显示,咬合形态与牙根形态影响移植位点周围骨应力分布;冠修复且根管治疗的自体移植牙应力分布更均匀,应力主要集中在冠部区域,可能降低牙根吸收风险。
要点
- 咬合形态与牙根形态影响自体移植牙周围骨的应力分布。
- 冠修复的自体移植牙应力更多集中于冠部区域。
- 冠修复联合根管治疗的自体移植牙应力分布更均匀。
核心结论
- 自体移植牙的咬合形态与牙根形态影响移植位点周围骨应力及牙齿生物力学响应。
- 冠修复牙应力分布更均匀且主要集中于冠部区域,可能降低牙根吸收风险。
研究设计与样本
- 采用有限元分析(FEA)构建7种不同自体移植牙情境模型,包括第一磨牙、第三磨牙、根管治疗第三磨牙、根管治疗且骨粘连第三磨牙、冠修复第三磨牙、冠修复且根管治疗第三磨牙、根管治疗且骨粘连并冠修复第三磨牙。
- 在咬合面施加200 N平行于牙长轴的负载,计算各情境牙本质与周围骨的最大von Mises应力。
主要发现
- 各模型间应力分布存在差异。
- 骨粘连模型中应力主要见于牙齿冠部区域。
- 冠修复模型较未冠修复模型应力更多见于牙齿冠部区域。
- 根管治疗且冠修复的自体移植牙应力分布均匀。
临床怎么用
- 作者认为,临床医生可考虑对自体移植牙进行冠修复以改善牙体结构内应力分布。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVE: The biomechanical response of an autotransplanted tooth and surrounding bone to occlusal loads is not well-known. The aim of the present study was to investigate the effect of root form and occlusal morphology on stress distribution in autotransplanted teeth and surrounding bone by using finite element analysis (FEA). METHODS: Seven FEA models representing different autotransplanted tooth situations were generated: (a) first molar, (b) third molar, (c) root canal-treated third molar, (d) root canal-treated, ankylosed, third molar, (e) crowned third molar, (f) crowned and root canal-treated third molar, (g) root canal-treated, ankylosed, and crowned third molar. Load (200 N) was applied on the occlusal surface, parallel to the long axis of the tooth. Maximum von Mises stress values on dentin and surrounding bone were calculated for each situation. RESULTS: Differences in stress distribution were observed among models. In ankylosed model, stress was primarily observed at the coronal region of the tooth. The stress was observed more at the coronal region of the tooth in crowned models compared with the non-crowned models. The stress distribution was homogeneous with root canal-treated and crowned autotransplanted tooth. CONCLUSIONS: The occlusal morphology and root form of the autotransplanted tooth affected the stress in surrounding bone at the transfer site and the biomechanical response of the tooth. The stress was more homogeneous in crowned tooth and primarily observed at the coronal region, which may decrease the risk for root resorption. CLINICAL SIGNIFICANCE: Root configuration, occlusal form and root canal treatment induce significant changes on the stress distribution on teeth and bone, including characteristic stress concentration and increased stress values. Clinicians can consider crowning autotransplanted teeth for improved stress distribution within the tooth structure.
引用
- Kırmalı Ö, Türker N, Akar T, et al. Finite element analysis of stress distribution in autotransplanted molars. J Dent. 2022. PMID: 35247471. doi:10.1016/j.jdent.2022.104082
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。