文献速递口腔修复与种植口腔正畸

一种用于3D打印的新型低收缩树脂

A Novel Low-Shrinkage Resin for 3D Printing.
PubMed 文献 · J Dent · 2022-01-14

本研究评估了一种新型光聚合3D打印树脂的体积收缩、精度和力学性能,并与三种商用树脂比较。新型树脂体积收缩显著更低、精度显著更高,弯曲和拉伸性能与Die and Model Tan树脂相似,但显著高于Formlabs Grey树脂、低于LCD Grey树脂。作者认为其适合用于修复、正畸和种植的模型制作。

要点

  • 新型树脂体积收缩显著低于三种商用树脂(p<0.001)。
  • 新型树脂打印精度显著高于其他商用树脂(p<0.001)。
  • 新型树脂弯曲强度、弯曲模量和拉伸强度与Die and Model Tan树脂相似(p>0.05)。

核心结论

  • 新型3D打印树脂相比商用树脂材料表现出更低的体积收缩、高精度和足够的力学性能。

研究设计与样本

  • 实验性体外研究,配制一种新型专有3D打印树脂,与Die and Model Tan(SprintRay)、Formlabs Grey(FormLabs)和LCD Grey(Roxel 3D)三种商用树脂进行比较。
  • 体积收缩采用AcuVol视频成像法测量;通过DLP打印系统确定打印物体的精度,以扫描模型与原始计算机辅助设计(CAD)数字模型之间的3D偏差评价。
  • 弯曲强度、弯曲模量和回弹模量采用平行六面体试件(2×2×25 mm,n=5)按ISO-4049测量;拉伸强度采用哑铃形试件(V型,n=5)按ASTM-D638测试。
  • 数据采用单因素方差分析和事后Tukey检验(p≤0.05)分析。

主要发现

  • 实验树脂的体积收缩显著低于其他商用树脂(p<0.001)。
  • 实验树脂的精度显著高于其他商用树脂(p<0.001)。
  • 实验树脂的弯曲强度、弯曲模量和拉伸强度与Die and Model Tan树脂(SprintRay)相似(p>0.05)。
  • 实验树脂的上述力学参数显著高于Formlabs Grey树脂(Formlabs)(p<0.001),且显著低于LCD Grey树脂(Roxel3D)(p<0.001)。

临床怎么用

  • 作者认为,新3D打印物体表现出更高精度、良好的时间稳定性和足够的力学性能,因此是用于修复、正畸和种植模型制作应用的良好候选材料。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: To evaluate the shrinkage, accuracy, and mechanical properties of a newly developed photo-polymerizable resin material for 3D printing dental applications and compare it with three commercially available resins. METHODS: An experimental novel proprietary resin material for 3D printing was formulated. This new resin, Die and Model Tan (SprintRay), Formlabs Grey (FormLabs), and LCD Grey (Roxel 3D) were evaluated and tested for volumetric shrinkage, accuracy, and flexural and tensile properties. Volumetric shrinkage was measured using the AcuVol video imaging method. The accuracy of the 3D printed objects through the DLP (digital light processing) printing system was determined by the 3D deviation between the scanned model and the original computer-aided-design (CAD) digital model. Parallelepiped specimens (2 × 2 × 25 mm, n = 5) were printed for flexural strength, flexural modulus, and modulus of resilience and measured in accordance with ISO-4049. Dumbbell-shaped specimens (Type V, n = 5) were printed to investigate the tensile strength and tested according to ASTM-D638. Data were analyzed using one-way ANOVA and post-hoc Tukey tests (p ≤ 0.05). RESULTS: The experimental resin exhibited significantly lower volumetric shrinkage and significantly higher accuracy than the other commercially available resins (p < 0.001). The experimental resin showed flexural strength, flexural modulus, and tensile strength similar to Die and Model Tan resin (SprintRay) (p > 0.05), and these parameters were significantly higher than those of Formlabs Grey resin (Formlabs) and lower than those of LCD Grey resin (Roxel3D)(p <0.001). CONCLUSION: The newly formulated 3D printing resin demonstrated lower volumetric shrinkage, high accuracy, and adequate mechanical properties compared to the commercially available resin materials. CLINICAL SIGNIFICANCE: The new 3D printed objects exhibited higher accuracy, good stability over time, and adequate mechanical properties; hence, it is a good candidate for modeling applications for restoration, orthodontics and implants.

来源:J Dent,查看原文。版权归原作者所有。

引用

  1. Ling L, Taremi N, Malyala R, et al. A Novel Low-Shrinkage Resin for 3D Printing. J Dent. 2022. PMID: 35038476. doi:10.1016/j.jdent.2022.103957

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。