工作长度处啄动次数对单锉系统在长卵形弯曲根管中成形能力的影响
本研究比较工作长度处啄动次数对单锉系统成形长卵形弯曲根管能力的影响。将预扫描配对的单根下颌前磨牙随机分为XP-endo Shaper、Reciproc Blue和WaveOne Gold三组(每组15例),分别进行1、2、4、10或20次啄动后复扫。结果显示啄动次数增加可提高切割效率,RB和WOG不超过4次、XPS不超过10次啄动即可接受。
要点
- 啄动次数增加使根尖部小直径和根管体积增加百分比增大,未预备根管表面积百分比减小(P < .05)。
- RB和WOG在4次啄动后D0处平均小直径为0.29至0.35 mm。
- XPS在10次啄动后D0处平均小直径为0.35至0.36 mm。
核心结论
- 增加啄动次数可提高单锉系统的切割效率,且不 adverse 改变卵形弯曲根管的解剖特征。
- 对于这些难以清洁的根管,RB和WOG系统不超过4次啄动、XPS系统不超过10次啄动似乎可接受。
研究设计与样本
- 采用微计算机断层扫描预扫描单根下颌前磨牙的长卵形弯曲根管(25°-35°),解剖配对后随机分为3组(n = 15)。
- 三组分别为XP-endo Shaper(XPS;FKG Dentaire,瑞士拉绍德封)、Reciproc Blue(RB;VDW,德国慕尼黑)和WaveOne Gold(WOG;Dentsply Sirona,瑞士巴莱格)。
- 预备至工作长度后,每个样本进行1、2、4、10或20次啄动至工作长度并复扫。
- 形态学参数采用双因素重复测量方差分析和Scheirer-Ray-Hare检验分析。
主要发现
- 根尖部小直径和根管体积增加百分比随啄动次数增加而增大,而未预备根管表面积百分比减小(P < .05)。
- RB和WOG系统4次啄动后D0处平均小直径(mm)在0.29至0.35之间。
- XPS系统10次啄动后D0处平均小直径(mm)在0.35至0.36之间。
- 各组在根管弯曲度和根管三分之一水平处的根管偏移或中心比率无显著差异(P > .05)。
关键数值与推荐
- RB和WOG系统不超过4次啄动、XPS系统不超过10次啄动似乎可接受用于这些难以清洁根管的成形。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: The present study compared the effect of the number of pecking motions at the working length (WL) on the shaping ability of single-file systems in long oval-shaped curved root canals. METHODS: Single-rooted mandibular premolars with long oval-shaped curved canals (25°-35°) were prescanned using micro-computed tomographic imaging, anatomically paired, and randomly divided into 3 groups (n = 15): XP-endo Shaper (XPS; FKG Dentaire, La Chaux-de-Fonds, Switzerland), Reciproc Blue (RB; VDW, Munich, Germany), and WaveOne Gold (WOG; Dentsply Sirona, Ballaigues, Switzerland). After preparation to the WL, each specimen underwent 1, 2, 4, 10, or 20 pecking motions to the WL and was rescanned. Morphologic parameters were measured and analyzed using a 2-factor repeated measures analysis of variance and the Scheirer-Ray-Hare test. RESULTS: The minor apical diameter and percentage increase in canal volume increased with the number of pecking motions, whereas the percentage of unprepared canal surface area decreased (P < .05). The mean minor diameters (in mm) at D0 varied between 0.29 and 0.35 after 4 pecking motions with the RB and WOG systems and between 0.35 and 0.36 after 10 pecking motions with the XPS system. No significant differences in canal transportation or centering ratio were observed among the groups at the levels of canal curvature and canal thirds (P > .05). CONCLUSIONS: Increasing the number of pecking motions improves the cutting efficacy of single-file systems without adversely altering the anatomic characteristics of oval-shaped curved canals. No more than 4 pecking motions for the RB and WOG systems and 10 pecking motions for the XPS system appear to be acceptable for the shaping of these difficult to clean root canals.
引用
- Wang L, Lin R, Chen H, et al. Influence of the Number of Pecking Motions at Working Length on the Shaping Ability of Single-file Systems in Long Oval-shaped Curved Canals. J Endod. 2022. PMID: 35081440. doi:10.1016/j.joen.2022.01.009
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。