文献速递先天性心脏病外科

3D打印心脏模型在大动脉调转术实操培训中的技术表现定量评估

Quantitative assessment of technical performance during hands-on surgical training of the arterial switch operation using 3-dimensional printed heart models.
PubMed 文献 · J Thorac Cardiovasc Surg · 2019-12-20

本研究纳入30名不同经验水平的外科医生,在Hands-on Surgical Training课程中于3D打印大动脉转位心脏模型上两次完成大动脉调转术,使用经验证的手术特异性评估工具回顾性评分。第二次操作时间显著缩短,平均差22分19秒(95%CI 15分22秒至25分34秒)。

要点

  • 3D打印模型重复实操可客观提升大动脉调转术的技术表现与操作速度。
  • 所有医生第二次操作均显著快于第一次,平均缩短22分19秒。

核心结论

  • 这是首个在3D打印心脏模型上客观证明大动脉调转术操作时间和技术表现改善的研究。
  • 结果表明,带有建设性客观反馈的刻意练习模拟对先心病外科医生培训至关重要。
  • 此类模拟与评估应纳入先心病外科结构化、标准化的培训课程。

研究设计与样本

  • 前瞻性培训课程中的重复操作研究,共30名不同经验水平的外科医生参与。
  • 每位医生在3D打印大动脉转位心脏模型上完成两次大动脉调转术。
  • 使用经验证的手术特异性评估工具Hands-on Surgical Training-Congenital Heart Surgery对60段录像回顾性评分。

主要发现

  • 第一次与第二次平均总分分别为103和120,平均差17(95%CI 10-24)。
  • 所有医生第二次操作均统计学显著更快。
  • 第一次与第二次平均时间分别为1小时28分4秒和1小时5分45秒。
  • 平均时间差为0小时22分19秒(95%CI 0小时15分22秒至0小时25分34秒)。

临床怎么用

  • 可将3D打印模型结合经验证评估工具用于先心病外科大动脉调转术的模拟培训。
  • 培训中应安排重复操作并提供客观、建设性的反馈以促进技术提升。
  • 建议将此类模拟与评估整合进结构化、标准化的先心病外科培训课程。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: Data supporting the use of hands-on simulation in congenital heart surgery are promising but primarily qualitative. This study aimed to demonstrate if there was an objective improvement in time and technical performance of the arterial switch procedure on 3-dimensional printed heart models by surgeons using a validated assessment method. METHODS: A total of 30 surgeons of varying experience performed the arterial switch procedure twice on 3-dimensional printed models with transposition of the great arteries during the Hands-on Surgical Training courses. Surgeons' performances were recorded and retrospectively assessed for both time and performance using the Hands-on Surgical Training-Congenital Heart Surgery tool, a validated procedure-specific assessment tool for the arterial switch. RESULTS: A total of 60 videos were scored. Eighty percent of surgeons (24/30) had improved from their first attempt. The mean total score of the first attempt performance compared with the second was 103 and 120, respectively, with a mean difference in score of 17 (95% confidence interval, 10-24). All surgeons were statistically significantly quicker in their second attempt. The mean time for the first attempt compared with the second was 1 hour, 28 minutes, 4 seconds and 1 hour, 5 minutes, and 45 seconds, respectively, with a mean difference of 0 hours, 22 minutes, 19 seconds (95% confidence interval, 0 hours, 15 minutes, 22 seconds to 0 hours, 25 minutes, 34 seconds). CONCLUSIONS: This is the first study to demonstrate an objective improvement in time and technical performance of the arterial switch procedure on 3-dimensional printed heart models. This supports the evidence that simulation in the form of deliberate practice with constructive, objective feedback is fundamental in the training of future congenital heart surgeons. These simulations and assessments should be incorporated to create structured, standardized training curricula within congenital heart surgery.

来源:J Thorac Cardiovasc Surg,查看原文。版权归原作者所有。

引用

  1. Hussein N, Honjo O, Haller C, et al. Quantitative assessment of technical performance during hands-on surgical training of the arterial switch operation using 3-dimensional printed heart models. J Thorac Cardiovasc Surg. 2019. PMID: 31983523. doi:10.1016/j.jtcvs.2019.11.123

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。