文献速递肺外科

胸外科手术规划:影像技术与三维打印比较的初步研究

Operative Planning in Thoracic Surgery: A Pilot Study Comparing Imaging Techniques and Three-Dimensional Printing.
PubMed 文献 · Ann Thorac Surg · 2018-10-11

本研究评估CT扫描、最大强度投影成像、三维重建及三维打印在解剖性肺切除术前界定肺门结构的能力。16例患者术前影像分析显示,CT、三维重建CT和最大强度投影图像倾向于低估动脉分支数量,与术中绝对一致性的评分在0.26至0.39之间;另3例肺门三维打印的测量最准确,相关性为0.92,但差异无统计学意义。结论提示三维打印在胸外科手术规划中可能优于现有影像模态。

要点

  • CT、三维重建CT和最大强度投影图像倾向于低估肺门动脉分支数量。
  • 三维打印肺门模型测量最准确,与术中相关性为0.92。
  • 三维打印在手术规划中的优势尚需进一步研究确立。

核心结论

  • 三维打印在胸外科手术规划中可能优于现有影像模态,但其在实操中的应用仍在建立中。

研究设计与样本

  • 单术者3个月期间连续纳入因癌症接受择期VATS肺切除的患者,分析16例术前影像并另对3例肺门进行三维打印,与术中所见比较。

主要发现

  • CT、三维重建CT和最大强度投影图像倾向于低估动脉分支数量,与术中动脉数量的绝对一致性评分在0.26至0.39之间。
  • 三维打印肺门模型的测量最准确,相关性为0.92,但差异无统计学意义。

关键数值与推荐

  • 三维打印肺门与术中动脉分支数量的相关性为0.92。
  • CT、三维重建CT和最大强度投影图像与术中动脉数量的绝对一致性评分在0.26至0.39之间。

临床怎么用

  • 在VATS解剖性肺切除术前,可考虑使用三维打印肺门模型辅助界定血管解剖,以减少对动脉分支数量的低估。

局限性

  • 样本量小(16例影像分析加3例三维打印),且三维打印的准确性优势未达统计学显著。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Careful preoperative planning in thoracic surgery is essential for positive outcomes, especially in video-assisted thoracic surgery (VATS), where palpation and 3-dimensional (3D) imaging is restricted. This study evaluated the ability of different imaging techniques, such as computed tomography (CT) scanning, maximal intensity projection imaging, 3D reconstruction, and 3D printing, to define the anatomy of the hilar structures before anatomical lung resection. METHODS: All patients undergoing elective lung resections by VATS for cancer under a single surgeon were identified over a 3-month period. The surgeon was asked to record the number of pulmonary artery branches supplying the lobe to be resected by using the preoperative CT scans, maximal intensity projection images, and 3D-reconstructed CT images. The lung hilum in 3 patients was printed. These were then compared with the intraoperative findings. RESULTS: The preoperative imaging of 16 patients was analyzed. The lung hilum was printed in a further 3 patients. Although not statistically significant, the 3D prints of the hilum were the most accurate measurement, with a correlation of 0.92. CT, 3D-reconstructed CT, and maximal intensity projection images tended to underrecognize the number of arterial branches and therefore scored between 0.26 and 0.39 in absolute agreement with the number of arteries found at operation. CONCLUSIONS: 3D printing in the planning of thoracic surgery may suggest a benefit over contemporary available imaging modalities, and the use of 3D printing in practicing operations is being established.

来源:Ann Thorac Surg,查看原文。版权归原作者所有。

引用

  1. Smelt JLC, Suri T, Valencia O, et al. Operative Planning in Thoracic Surgery: A Pilot Study Comparing Imaging Techniques and Three-Dimensional Printing. Ann Thorac Surg. 2018. PMID: 30316856. doi:10.1016/j.athoracsur.2018.08.052

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。